SOLZAIMA Hidro 12 Скачать руководство пользователя страница 119

Страница: 119 / 147

113

WARNING!

After the restart, the LED display shows the previously set values of

the pump.

Lock/unlock the button

- To activate the key lock, press and hold the operating button for 8 seconds until
the LEDs for the selected setting briefly flash, then release.

- LEDs flash constantly at 1-second intervals.

- The key lock is activated: pump settings can no longer be changed.

- The key lock is deactivated in the same manner as it is activated.

Figure 80 - Lock/unlock the button

Activating factory setting

- The factory setting is activated by pressing and holding the operating button whilst
switching off the pump.

- Press and hold the operating button for at least 4 seconds.

- All LEDs flash for 1 second.

- The LEDs for the last setting flash for 1 second.

- When the pump is switched on again, the pump runs using the factory settings

(delivery condition).

Содержание Hidro 12




















































































































































Результаты поиска

Содержание Hidro 12

Отзывы:

Похожие инструкции для Hidro 12

Бренды по названию

Популярные бренды

SOLZAIMA Hidro 12, Инструкция по эксплуатации

Результаты поиска

Содержание Hidro 12

Отзывы:

Похожие инструкции для Hidro 12

Бренды по названию

Популярные бренды