SOLZAIMA Hidro 12 Скачать руководство пользователя страница 118

Страница: 118 / 147

112

LED display

Control mode

Pump curve

Constant speed.

III

Table 12 - Control mode

Functions

Venting

If the pump does not vent automatically:

- Activate the pump venting function via the operating button, press and hold for 3
seconds, then release.

- The pump venting function is initiated and lasts 10 minutes.

- The top and bottom LED rows flash in turn at 1 second intervals.

- To cancel, press and hold the operating button for 3 seconds.

Manual restart

The pump attempts an automatic restart upon detecting a blockage.

If the pump does not restart automatically:

- Activate manual restart via the operating button: press and
hold for 5 seconds, then release.

- The restart function is initiated, and lasts max. 10 minutes.

- The LEDs flash in succession clockwise.

- To cancel, press and hold the operating button for 5
seconds.

Figure 79 - Manual restart

Содержание Hidro 12




















































































































































Результаты поиска

Содержание Hidro 12

Отзывы:

Похожие инструкции для Hidro 12

Бренды по названию

Популярные бренды

SOLZAIMA Hidro 12, Инструкция по эксплуатации

Результаты поиска

Содержание Hidro 12

Отзывы:

Похожие инструкции для Hidro 12

Бренды по названию

Популярные бренды