Solare Datensysteme Solar-Log Скачать руководство пользователя страница 126

Страница: 126 / 506

126

Fronius

Fronius

32.1

Fronius with ComCard

Termination

Addressing

Interface

Connection plug

Bridge 4-3 + 5-6

Yes

RS422

Select “Fronius: SolarNet“ during the inverter detection.

Overview

•

The Fronius ComCard RS422 interface integrated as an option;
otherwise can be retrofitted using "ComCard retrofit".

•

Where to connect: RJ45 socket on the outside of the inverter.

•

4 wire cabling with 6-pin terminal block connector.

•

Communication address must be allocated:

Recommendation: Continuous numbering starting with 1.

Setting: Using the inverter operating display.

Procedure: Start according to the inverter's instructions.

•

Installation steps:

•

Switch off the inverters and Solar-Log™.

•

(Install Fronius ComCard RS485 interface into the inverter).

•

Connect inverters to the Solar-Log™.

•

Connect the inverters to each other.

•

Allocate communication address.

Installing Fronius ComCard RS422 interface

Procedure

►

Install the Fronius ComCard RS422 interface in the inverter in accordance with the interface card installation
instructions.

Connect inverters to the Solar-Log™

The wiring is done using a

•

ready-made Fronius data cable (optional extra; not supplied)

•

self-made data cable with RJ45 plug and 6-pin terminal block connector.

Caution

Risk of damage to the unit!
The Solar-Log™ also has an RJ45 socket, which must never be connected to the RJ45 socket on the
inverter.

►

►Only connect inverters via the RS485/422 B or C-Solar-Log™ interface.

Содержание Solar-Log



























































































































































































































































































































































































































































































































Результаты поиска

Содержание Solar-Log

Отзывы:

Похожие инструкции для Solar-Log

Бренды по названию

Популярные бренды

Solare Datensysteme Solar-Log, Руководство по подключению компонентов

Результаты поиска

Содержание Solar-Log

Отзывы:

Похожие инструкции для Solar-Log

Бренды по названию

Популярные бренды