manualshive.com logo in svg

Solare Datensysteme Solar-Log, Руководство по подключению компонентов


Поделиться
Скачать
background image

244

REFUSOL

or if the system is extended. In these cases the new inverters must also be provided with the extended parameters 
again.

The extended parameters are only available starting from inverter firmware version 800.2.20 or higher. The firm-
ware version can be checked on the inverter menu:

 

►

"F1" /

 Numerical list

 / Parameters 1.1 to 1.3

Current firmware versions and update instructions can be found at 

www.refu-elektronik.com/en

.

Set the following parameters on the inverter's operating display:
1.  Press "F1"
2. 

Select 

Numerical list

, press "ENTER".

3.  Set parameter number 

0407

 press "ENTER"

4.  Select sub parameter 0407,3, press "ENTER"
5.  Enter "2"  

[Communication type RS485: Solarlog], press "ENTER".31], press "ENTER".

6.  Set parameter number 

0420

 press "ENTER"

7.  Select sub parameter 

0420,3,

 press "ENTER"

8.  Enter the numerical value 

9600,

 press "ENTER"

9.  Using the installed DC isolating switch turn the inverters on and off briefly so that the settings are activated.

Note

The numerical value "2" under point 5 in the settings refers to the old Solar-Log protocol and the value 
"1" to the native protocol for active and reactive power control.
The value under point 8 refers to the inverter's baud rate and is 9600 for the old Solar-Log protocol 
and 57600 for the native protocol.

Allocate communication address

• 

Recommendation: Continuous numbering starting with 1.

• 

Setting: Using the inverter operating display

• 

Procedure: Start according to the inverter's instructions

Note

To use active and reactive power management, all of the inverters need to be set to:

• 

Protocol 1

• 

57600 baud 

• 

Parameter 1164 = 2

Note 

A maximum of 31 inverters can be connected per RS485 bus.

Содержание Solar-Log



























































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для Solar-Log

Computech DATAMAXX Manual preview
DATAMAXX
Бренд: Computech Страницы: 49
Switrace I-PLUG pdf Multi-use User Manual preview
I-PLUG pdf Multi-use
Бренд: Switrace Страницы: 10
Omega HHAQ-104 User Manual preview
HHAQ-104
Бренд: Omega Страницы: 14
Microtronics myDatalogEx User Manual preview
myDatalogEx
Бренд: Microtronics Страницы: 84
Dickson KT6 User Manual preview
KT6
Бренд: Dickson Страницы: 4
Geokon GK-404 Instruction Manual preview
GK-404
Бренд: Geokon Страницы: 24
Blumax GPS-4044 User Manual preview
GPS-4044
Бренд: Blumax Страницы: 36
Theodor Friedrichs COMBILOG 1020 Hardware Manual preview
COMBILOG 1020
Бренд: Theodor Friedrichs Страницы: 170
Somat eDAQlite User Manual preview
eDAQlite
Бренд: Somat Страницы: 228
Eagle Tree Systems Dual A/D Expander V2 Instruction Manual preview
Dual A/D Expander V2
Бренд: Eagle Tree Systems Страницы: 2
Ohkura VM7000A Operation Manual preview
VM7000A
Бренд: Ohkura Страницы: 61
Ebro EBI 100 Series Manual preview
EBI 100 Series
Бренд: Ebro Страницы: 40
Omega OM-WEB-TC User Manual preview
OM-WEB-TC
Бренд: Omega Страницы: 43
Accsence VersaLog User Manual preview
VersaLog
Бренд: Accsence Страницы: 70
Geosense GEOLOGGER G8 PLUS Advanced Instruction Manual preview
GEOLOGGER G8 PLUS
Бренд: Geosense Страницы: 30
Enerdis Elog Getting Started Manual preview
Elog
Бренд: Enerdis Страницы: 4
Dickson PR120 Quick Start Manual preview
PR120
Бренд: Dickson Страницы: 2
RST Instruments RSTAR Affinity Gateway Installation Manual preview
RSTAR Affinity Gateway
Бренд: RST Instruments Страницы: 24

Бренды по названию

Популярные бренды

Загрузить еще бренды