Solare Datensysteme Solar-Log Скачать руководство пользователя страница 112 | Manualshive

Страница: 112 / 506

Solare Datensysteme Solar-Log Скачать руководство пользователя страница 112

112

EHE

26.3

EHE N250k to N500k-TL

Termination

Addressing

Interface

Yes

Yes

RS485

The following types are to be connected according to this diagram:

•

N250K, N250K-TL, N500K-TL

Overview

•

Integrated interface.

•

Where to connect: Terminal strip inside the inverter.

•

2-pin wiring.

•

Communication address must be allocated.

•

Installation steps:

•

Switch off the inverters and Solar-Log™.

•

Connect inverters to the Solar-Log™.

•

Connect the inverters to each other.

•

Enter the communication address on the interver's display.
Every address may only be used once.
Address range 1 to 247.

Connect inverters to the Solar-Log™

The wiring is done using a

•

self-made cable connection with terminal block connector.

•

Where to connect: Terminal strip inside the inverter.

Procedure

1. If you are making the cable yourself, connect the wires as shown in the following diagram:

Solar-Log™ terminal strip connector

Terminal strip inside the inverter

Terminal

Terminal

►

1 (Data+)

►

JX9 - A

►

4 (Data-)

►

JX9 - B

2. If no further inverter is connected, terminate the inverter according to the instructions for the inverter.
3. Insert the terminal block connector into the Solar-Log™ RS485 socket.

Connect the inverters to each other

•

Connect with a shielded twisted-pair cable.

•

Where to connect: Terminal strip inside the inverter.

«
...
110
111
112
113
114
...
»

Содержание Solar-Log



























































































































































































































































































































































































































































































































Отзывы:

Нет отзывов