manualshive.com logo in svg

Solare Datensysteme Solar-Log, Руководство по подключению компонентов


Поделиться
Скачать
background image

317

SolarEdge

Procedure

1.  Open the inverter as shown in the inverter's instructions.
2.  Pull the free wires through the wire opening in the inverter.
3.  If you are making the cable yourself, connect the wires as shown in the following diagram:

Solar-Log™ terminal strip connector

X4 socket RS485-1 inverter

Terminal

PIN

 

►

1

A - Data+

 

►

3

G  - GND

 

►

4

B - Data-

4.  If no further inverter connected, terminate the inverter with DIP switch SW7 according to the manufacturer's 

instructions.

5.  Screw the inverter cover on again.
6.  Insert the terminal block connector into the Solar-Log™ RS485 socket.

Connect the inverters to each other

• 

Where to connect: Terminal strip inside the inverter

Procedure

1.  Open the inverter as shown in the inverter's instructions.
2.  Pull the free wires through the wire opening in the inverter.
3.  If you are making the cable yourself, connect the wires as shown in the following diagram:

X4 socket RS485-1 inverter n

X4 socket RS485-1 inverter n+1

PIN

PIN

A - Data+

A - Data+

G  - GND

G  - GND

B - Data-

B - Data-

4.  Connect the other inverters to each other in the same way.
5.  Terminate the last inverter with DIP switch SW7 according to the manufacturer's instructions.
6.  Screw the inverter cover on again.
7.  Insert the terminal block connector into the Solar-Log™ RS485 socket.

Allocate communication address

• 

Recommendation: Continuous numbering starting with 1; highest possible address: 247.

• 

Setting: Using the inverter operating display

• 

Procedure: Start according to the inverter's instructions

Inverter settings 

Two settings need to be checked on the inverter's control panel and changed if needed before performing the 
inverter detection.
1. 

Non-SE Logger

 has to be set in the  

Communication // RS485-1 Conf // Device Type 

 menu.

2. 

SunSpec 

 has to be activated in the 

Communication // RS485-1 Conf // Protocol

 menu.

Содержание Solar-Log



























































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для Solar-Log

Meilhaus Electronic RedLab WebDAQ 316 User Manual preview
RedLab WebDAQ 316
Бренд: Meilhaus Electronic Страницы: 31
Microtronics myDatalog4 User Manual preview
myDatalog4
Бренд: Microtronics Страницы: 145
XC-Tracer Maxx User Manual preview
Maxx
Бренд: XC-Tracer Страницы: 16
Salient Systems intellitrack Reader Manual preview
intellitrack Reader
Бренд: Salient Systems Страницы: 21
Xylem YSI Storm 3 Getting Started Manual preview
YSI Storm 3
Бренд: Xylem Страницы: 18
Omega OM-CP-PROCESS101A Instruction Sheet preview
OM-CP-PROCESS101A
Бренд: Omega Страницы: 5
Bosch C 80 Manual preview
C 80
Бренд: Bosch Страницы: 144
Wilmers blueberry COMPACT Manual preview
blueberry COMPACT
Бренд: Wilmers Страницы: 48
Hobo RX3003 Quick Start preview
RX3003
Бренд: Hobo Страницы: 2
Hobo MX2306 Manual preview
MX2306
Бренд: Hobo Страницы: 9
Hobo MX1104 Manual preview
MX1104
Бренд: Hobo Страницы: 12
Termoprodukt TERMIO-15 User Manual preview
TERMIO-15
Бренд: Termoprodukt Страницы: 18
Rockwell Automation 1441-DYN25-MBMP User Manual preview
1441-DYN25-MBMP
Бренд: Rockwell Automation Страницы: 34
Rockwell Automation 1441-DYN25-MRUC User Manual preview
1441-DYN25-MRUC
Бренд: Rockwell Automation Страницы: 50
peoplenet eDriver Logs Quick Reference Manual preview
eDriver Logs
Бренд: peoplenet Страницы: 15
DeLUX iU-01W Operation Instruction Manual preview
iU-01W
Бренд: DeLUX Страницы: 15
berlinger SmartMonitor SITE L Operator'S Manual preview
SmartMonitor SITE L
Бренд: berlinger Страницы: 26
M.C. MILLER VoltTab User Manual preview
VoltTab
Бренд: M.C. MILLER Страницы: 13

Бренды по названию

Популярные бренды

Загрузить еще бренды