Solare Datensysteme Solar-Log Скачать руководство пользователя страница 461 | Manualshive

Страница: 461 / 506

Solare Datensysteme Solar-Log Скачать руководство пользователя страница 461

461

VARTA Battery System

Procedure for IP addresses assignment:

In addition to a static, fixed IP, a dynamic IP address can also be assigned.

Dynamic IP adress:

Both devices, the Solar-Log ™, and the VARTA battery system must be provided automatically to IP address (DHCP).

Static IP adress:

•

Please select an IP address with the same class C subnet as the Solar-Log™.
For example: The Solar-Log™ has the IP address 192.168.178.49.
The battery system in this case has to have a free IP address in the same range (from 192.168.178.1 to
192.168.178.254).

•

Procedure: Start according to the battery system‘s instructions.

Detection via the Solar-Log

™

WEB interface

•

For the device detection on the Solar-Log

™

select „VARTA:Industrial“ in the

Network

section from the

Configu-

ration | Devices | Definition

menu.

•

Also select the proper interfaces for the meters as well as the inverters. Confirm the selection by clicking on

Save

.

Detection from the Solar-Log 1200

When using the Solar-Log 1200, the detection can also be started from the display.

•

Select „VARTA:Industrial“ from the „Network“ interface for the detection.

•

Also select the proper interfaces for the meters as well as the inverters and then start the detection.

Note

Only one battery system can be connected to a Solar-Log™ device.

Note

If a Varta consumption meter is connected to the battery system, an additional consumption meter
(bi-direction meter) is detected and recorded by the Solar-Log™ when it is detected. (The consumption
meter is active after the detection.)

Note

The Varta Industrial battery system cannot be used with the Solar-Log 50.

«
...
459
460
461
462
463
...
»

Содержание Solar-Log



























































































































































































































































































































































































































































































































Отзывы:

Нет отзывов