Siemens SIPART PS2 PA 6DR55 Series Скачать руководство пользователя страница 180

Страница: 180 / 292

Functions/operations using PROFIBUS PA

11.2 Acyclic data transfer

SIPART PS2 with PROFIBUS communication

180

Operating Instructions, 09/2007, A5E00127926-07

The above target modes are effective when the positioner is in the automatic mode (AUT). If

the positioner is in the manual mode (MAN), they are effective only after an on-site

switchover to the automatic mode (AUT).
These target modes are saved in the positioner in the power failure-safe manner.

Automatic mode

As long as the positioner is not integrated into the cyclic service as a slave, SIMATIC PDM

can be used to send a setpoint to it in a cyclic manner.
Configure the following settings:
1.

Go to the "Operating mode" tab.

Set the target mode to "Automatic".

Enter a value between 0 and 100% for the desired setpoint, quality as "Good" and the

status as "OK".

Transfer these settings to the positioner.

The positioner is controlled using the desired setpoint until a cyclic master starts

communication with a slave or you switch over the positioner to the "Manual" mode on-site.

Note
Note that the positioner responds with the "Poor" quality and the "Constant value" status

after sending the data.
If you exit this target mode and no other master sends a setpoint to the positioner, it is

controlled using the configured fail-safe value after the set monitoring time expires.

Manual mode

You can use SIMATIC PDM to send a setpoint to the positioner even when cyclic

communication is active. You must have priority over the cyclic master.
Configure the following settings:
1.

Go to the "Operating mode" tab.

Set the target mode to "Manual".

Enter a value between 0 and 100% as a starting value, quality as "Good" and the status

as "OK".

Transfer these settings to the positioner.

The positioner is now controlled using the desired starting value and reports this manual

mode through "MM" on the digital display.
Note that the starting value entered in the manual mode is directly written in the starting

block of the positioner without scaling.
You can switch the positioner to the manual mode on-site and move the actuator using

buttons. The setpoint is tracked as per the current actual value. The manual mode and the

current position are retained after switching back to the automatic mode.
After a power failure, the positioner is controlled in the manual mode depending on the

direction of action of the actuator using the value set in the "YA" or "YE" parameters.

Содержание SIPART PS2 PA 6DR55 Series





































































































































































































































































































Результаты поиска

Содержание SIPART PS2 PA 6DR55 Series

Отзывы:

Похожие инструкции для SIPART PS2 PA 6DR55 Series

Бренды по названию

Популярные бренды

Siemens SIPART PS2 PA 6DR55 Series, Руководство по эксплуатации

Результаты поиска

Содержание SIPART PS2 PA 6DR55 Series

Отзывы:

Похожие инструкции для SIPART PS2 PA 6DR55 Series

Бренды по названию

Популярные бренды