manualshive.com logo in svg

Siemens SINUMERIK 810D, Руководство по диагностике

Скачайте бесплатное руководство по диагностике Siemens SINUMERIK 810D на manualshive.com. Это необходимое руководство поможет в обслуживании и ремонте оборудования. С SINUMERIK 810D вы сможете улучшить производительность своего производства и обеспечить качественное выполнение задач. Скачайте его сейчас!

Поделиться
Скачать
background image

SIMODRIVE alarms

11/2006

Overview of Alarms

 

2-787

©

 Siemens AG, 2006. All rights reserved

SINUMERIK, SIMODRIVE Diagnostics Manual (DA), 11/2006 Edition

 

310709

Axis %1 drive %2 error in piston diameter or piston rod diameter

Parameters:

%1 = NC axis number
%2 = Drive number

Definitions:

The piston diameter in drive MD 5131: CYLINDER_PISTON_DIAMETER is less than or equal to zero 
or the piston rod diameter in drive MD 5132: CYLINDER_PISTON_ROD_A_DIAMETER is greater 
than the piston diameter in drive MD 5131: CYLINDER_PISTON_DIAMETER or the piston rod 
diameter in drive MD 5133: CYLINDER_PISTON_ROD_B_DIAMETER is greater than the piston 
diameter in drive MD 5131: CYLINDER_PISTON_DIAMETER.

Reaction:

NC not ready.
The NC switches to follow-up mode.
Channel not ready.
NC Start disable in this channel.
Interface signals are set.
Alarm display.
NC Stop on alarm.

Remedy:

Enter a valid piston diameter in drive MD 5131: CYLINDER_PISTON_DIAMETER (0 < D <= 500mm). 
or Enter a piston rod diameter in drive MD 5132: CYLINDER_PISTON_ROD_A_DIAMETER which is 
less than the piston diameter in drive MD 5131: CYLINDER_PISTON_DIAMETER or Enter a piston 
rod diameter in drive MD 5133: CYLINDER_PISTON_ROD_B_DIAMETER which is less than the 
piston diameter in drive MD 5131: CYLINDER_PISTON_DIAMETER.

Program 
Continuation:

Switch control OFF - ON.

310710

Axis %1 drive %2 distance-coded scale incorrectly parameterized

Parameters:

%1 = NC axis number
%2 = Drive number

Definitions:

If a distance-coded scale is selected (MD 5011 bit 7=1) a length measuring system must also be 
configured (MD 5011 bit 4=1).

Reaction:

Mode group not ready.
Channel not ready.
NC Start disable in this channel.
Interface signals are set.
Alarm display.
NC Stop on alarm.

Remedy:

Check and, if necessary, correct MD 5011: ACTUAL_VALUE_CONFIG (actual value sensing 
configuration).

Program 
Continuation:

Switch control OFF - ON.

310750

Axis %1 drive %2 feedforward gain too high

Parameters:

%1 = NC axis number
%2 = Drive number

Definitions:

The feedforward control gain is calculated from the reciprocal of the gain in drive MD 5435: 
CONTROLLED_SYSTEM_GAIN.

Reaction:

NC not ready.
The NC switches to follow-up mode.
Channel not ready.
NC Start disable in this channel.
Interface signals are set.
Alarm display.
NC Stop on alarm.
Channel not ready.

Remedy:

Increase the speed controller cycle time in MD 5001: SPEEDCTRL_CYCLE_TIME.
Reduce the force controller feedforward factor in MD 5247: FORCE_FFW_WEIGHT.
Increase the gain in MD 5435: CONTROLED_SYSTEM_GAIN.

Program 
Continuation:

Clear alarm with the RESET key in all channels. Restart part program.

Содержание SINUMERIK 810D

















































































































































































































































































































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для SINUMERIK 810D

YASKAWA P1000 Quick Start Manual preview
P1000
Бренд: YASKAWA Страницы: 256
Aastra Aastra 620d Quick User Manual preview
Aastra 620d
Бренд: Aastra Страницы: 30
UCS CAT Quick Start Manual preview
CAT
Бренд: UCS Страницы: 4
Jabra Link 14201-10 How Do preview
Link 14201-10
Бренд: Jabra Страницы: 4
Xylem FST Installation, Operation And Maintenance Manual preview
FST
Бренд: Xylem Страницы: 48
Eaton EZD Series User Manual preview
EZD Series
Бренд: Eaton Страницы: 448
Eaton EC4E-221-6D4T1 Hardware And Engineering preview
EC4E-221-6D4T1
Бренд: Eaton Страницы: 57
tell Compact-GSM Installation And Application Manual preview
Compact-GSM
Бренд: tell Страницы: 11
CIAT CIATControl OPC Server Installation And Operating Instructions Manual preview
CIATControl OPC Server
Бренд: CIAT Страницы: 32
Challenger Lifts EnviroLift EW0820S090 Installation, Operation & Maintenance Manual preview
EnviroLift EW0820S090
Бренд: Challenger Lifts Страницы: 23
Danfoss AFD 2 VFG 2 Operating Manual preview
AFD 2 VFG 2
Бренд: Danfoss Страницы: 8
Bailey Infi 90 IMAOM01 Instructions Manual preview
Infi 90 IMAOM01
Бренд: Bailey Страницы: 44
Invertek Optidrive Elevator Quick Start Up Manual preview
Optidrive Elevator
Бренд: Invertek Страницы: 5
Techtrol TLIC Instruction And Programming Manual preview
TLIC
Бренд: Techtrol Страницы: 4
FOR-A HVS-2000-2SI Installation Manual preview
HVS-2000-2SI
Бренд: FOR-A Страницы: 6
turck CODESYS 3 Getting Started preview
CODESYS 3
Бренд: turck Страницы: 45
Thermo Scientific CC58114PBC Installation And Operation Manual preview
CC58114PBC
Бренд: Thermo Scientific Страницы: 68
Falco VL35F230B Installation And Operating Instructions Manual preview
VL35F230B
Бренд: Falco Страницы: 65

Бренды по названию

Популярные бренды

Загрузить еще бренды