Siemens SINUMERIK 810D Скачать руководство пользователя страница 301 | Manualshive

Страница: 301 / 880

background image

NCK alarms

11/2006

Overview of Alarms

2-301

©

Siemens AG, 2006. All rights reserved

SINUMERIK, SIMODRIVE Diagnostics Manual (DA), 11/2006 Edition

16773

Channel %1 axis %2 is the following axis. The axis/spindle disables of
leading axes %3 and %4 differ from one another.

Parameters:

%1 = Channel number
%2 = Axis, spindle
%3 = Axis, spindle
%4 = Axis, spindle

Definitions:

The axis is active in a coupling as a following axis. The master axes
have different states regarding axis/spindle disable.
The alarm can be suppressed with machine data 11415 SUPPRESS_ALARM_MASK_2 Bit0 =1.

Reaction:

Alarm display.

Remedy:

Set the same axis/spindle disable for all master axes.

Program
Continuation:

Alarm display showing cause of alarm disappears. No further operator action necessary.

16774

Channel %1 Synchronization aborted for slave axis/spindle %2

Parameters:

%1 = Channel number
%2 = Axis name, spindle number

Definitions:

For the indicated axis, the synchronization procedure (EGONSYN or EGONSYNE) was aborted.

There are several reasons for aborting the synchronization process:
   - RESET
   - End of program
   - Axis goes to follow-up mode
- Rapid stop caused by an alarm

Reaction:

NC Start disable in this channel.
Interface signals are set.
Alarm display.
NC Stop on alarm.
Channel not ready.

Remedy:

If the abort of the synchronization procedure can be tolerated or is intended, the alarm can be
suppressed with machine data 11410 SUPPRESS_ALARM_MASK Bit31 = 1.
Only applicable for electronic gear (EG):
If it is not possible to abort the synchronization procedure, you can achieve it by specifying the block
change criterion FINE in EGONSYN or EGONSYNE.

Program
Continuation:

Clear alarm with the RESET key. Restart part program

16776

Channel %1 block %2 curve table %3 does not exist for axis %4

Parameters:

%1 = Channel number
%2 = Block number, label
%3 = Number of curve table
%4 = Axis name, spindle number

Definitions:

An attempt was made to couple axis %4 with curve table number %3, but no curve table of this number
exists.

Reaction:

NC Start disable in this channel.
Interface signals are set.
Alarm display.
NC Stop on alarm.

Remedy:

Modify the NC part program so that the required curve table exists when axis link is to be activated.

Program
Continuation:

Clear alarm with the RESET key. Restart part program

«
...
299
300
301
302
303
...
»

Содержание SINUMERIK 810D

















































































































































































































































































































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для SINUMERIK 810D

Бренд: D-Link Страницы: 113

Бренд: D-Link Страницы: 146

Бренд: FAAC Страницы: 12

Бренд: Zetkama Страницы: 6

Бренд: Facility Explorer Страницы: 4

Бренд: OMA Страницы: 73

Бренд: CALEFFI Страницы: 2

Бренд: CALEFFI Страницы: 12

Бренд: Caliber Страницы: 6

Бренд: GAUGEMASTER Страницы: 2

Бренд: EasyIO Страницы: 19

Бренд: Zero 88 Страницы: 2

Бренд: Zenit Страницы: 24

COOPER POWER SERIES

Бренд: Eaton Страницы: 50

Бренд: Van Air Страницы: 4

Бренд: M-system Страницы: 3

Бренд: M-system Страницы: 103

Бренд: M-system Страницы: 13

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды