Siemens HiPath 1100 Скачать руководство пользователя страница 76

Страница: 76 / 241

Step by step

Programming an extension

The Dialing mode designates the dialing method as

pulse (DP), tone (DTMF) or automatic detection.

Required:

Programming mode must be activated (*95

31994).

ejl

Enter the programming code.

Enter the extension number (e.g., 12/102).

d . f

Enter the code for the dialing mode:

= Automatic identification (default)

= Pulse (DP)

= Multifrequency (MF)

Enter the next extension number

Press this key.

Initial status for programming mode.

Flash detection time

The Flash detection time is the maximum period of

time required by a PABX to detect a flash signal gener-

ated by an internal telephone. If older MF dialing tele-

phones are connected to the system, it may be neces-

sary to adjust the Flash detection time to their response

times (see manufacturer’s instructions). The specified

Flash detection time may vary for different countries.

Required:

Programming mode must be activated (*95

31994).

ege

Enter the programming code.

Enter the extension number (e.g. 12/102).

dde . fid

Enter the Flash detection time (001 to 250, in cycles of

10 ms). 001 = 10ms ... 010 = 100 ms ... 035 = 350 ms,

etc.

Enter the next extension number.

Default:

• 035 - Portugal, Argentina and Thailand

• 036 - for Korea

• 028 - for all other countries.

Содержание HiPath 1100


















































































































































































































































Результаты поиска

Содержание HiPath 1100

Отзывы:

Похожие инструкции для HiPath 1100

Бренды по названию

Популярные бренды

Siemens HiPath 1100, Руководство по программированию

Результаты поиска

Содержание HiPath 1100

Отзывы:

Похожие инструкции для HiPath 1100

Бренды по названию

Популярные бренды