Siemens HiPath 1100 Скачать руководство пользователя страница 158

Страница: 158 / 241

Step by step

Digital trunk settings

158

Initial status for programming mode.

TME1 module

The TME1 module can be configured to operate with E1

CAS access or S2 access. To determine the number of

analog and digital lines that will be available in the sys-

tem, see Service Manual - "Considerations for digital

lines in the HiPath 1150/1190".

This feature only works in ISDN lines in PP or

PMP mode and only with T-Reference Point.

The TME1 module is factory configured to oper-

ate as an E1 CAS interface.

In order for the module to work as a S2 interface

you must run a reconfiguration procedure using

the S2M Maintenance tool.

When the total number of digital trunks config-

ured for the module plus the number of analog

trunks exceeds the maximum capacity of the

system, the analog trunks for the EB 202, 206

and 210 expansion modules are deactivated.

Nevertheless, the extensions will continue to

work as usual. Lines are deactivated in the order

that they are physically installed (1, 2, etc.). This

process continues until the total number equals

the required number of trunks. The remaining

modules continue to operate as usual.

However, in the case of the EB 200, 400 and 800

modules, it is strongly recommended that you

change their slots to prevent their deactivation.

These modules become inoperable if any one of

their external line slots is deactivated.

Содержание HiPath 1100


















































































































































































































































Результаты поиска

Содержание HiPath 1100

Отзывы:

Похожие инструкции для HiPath 1100

Бренды по названию

Популярные бренды

Siemens HiPath 1100, Руководство по программированию

Результаты поиска

Содержание HiPath 1100

Отзывы:

Похожие инструкции для HiPath 1100

Бренды по названию

Популярные бренды