Siemens HiPath 1100 Скачать руководство пользователя страница 43

Страница: 43 / 241

External line settings

Step by step

Seizure priority by type of external line

External lines can be accessed using Code 0 or the

code for the group of lines (e.g: 890). If the switch has

analog and digital lines, you can configure the type of

line that will be given priority.

Required:

Programming mode must be activated (*95

31994).

emh

Enter the programming code.

...

Select the type of line:

= Independent seizure of the type of line (default).

In this case the seizure is sequential and cyclic.

= External digital lines are activated as first option.

= Analog trunks are activated as first option.

Initial status for programming mode.

Analog trunk seizure protocol

This feature specifies the protocol to be used by the

system for seizing an analog trunk, based on the local

carrier’s information.

Required:

Programming mode must be activated (*95

31994).

dek

Enter the programming code.

Enter a number for an analog trunk (e.g., 801).

...

Select the type of protocol:

= LOOP seizure (default for other countries)

= GROUND seizure (default for Canada)

Press this key.

Initial status for programming mode.

Caller ID for analog lines

When using the GROUND option for Canada, the

"Type of answering signal" feature for these ex-

ternal lines must be deactivated.

Содержание HiPath 1100


















































































































































































































































Результаты поиска

Содержание HiPath 1100

Отзывы:

Похожие инструкции для HiPath 1100

Бренды по названию

Популярные бренды

Siemens HiPath 1100, Руководство по программированию

Результаты поиска

Содержание HiPath 1100

Отзывы:

Похожие инструкции для HiPath 1100

Бренды по названию

Популярные бренды