Siemens HiPath 1100 Скачать руководство пользователя страница 147

Страница: 147 / 241

Fax/DID

147

Step by step

Press this key.

Initial status for programming mode.

Releasing Fax/DID after a timeout

When a Fax/DID Module is answering 8 calls simulta-

neously, the next call will receive a ring signal generated

by the local carrier until the HiPath 1100 answers the

call. If the timeout specified for this feature is shorter

than the local carrier’s timeout, the call can be routed in

two different ways, depending whether the PABX re-

ceived it over an analog or a digital line:

• For an analog trunk, the switch is required to bypass

the Fax/DID and forward calls to an analog line atten-

dant (if there is no attendant available, the call is for-

warded to an overflow extension). Of course, if a

Fax/DID channel becomes available in the mean-

time, the call will be answered as usual and the tim-

eout will be ignored.

However, if the time specified for this setting is

longer than the local carrier’s timeout (1.5 minutes

for Brazil), the call will be disconnected by the local

carrier before the PABX can forward it to an atten-

dant.

• In the case of a digital line (E1 CAS, S2 or S

access),

the PABX sends a "disconnect" signal to the line

upon receiving the call. This means that the time

specified for this setting is ignored in the case of dig-

ital lines. When the Fax/DID is busy answering 8 si-

multaneous calls, the external caller hears a busy

signal.

Required:

Programming mode must be activated (*95

31994).

dmh

Enter the programming code.

...

Enter the delay time (00 to 99 in cycles of 5 seconds)

where 00 = 0 seconds... 06 = 30 seconds (default), etc.

Initial status for programming mode.

Содержание HiPath 1100


















































































































































































































































Результаты поиска

Содержание HiPath 1100

Отзывы:

Похожие инструкции для HiPath 1100

Бренды по названию

Популярные бренды

Siemens HiPath 1100, Руководство по программированию

Результаты поиска

Содержание HiPath 1100

Отзывы:

Похожие инструкции для HiPath 1100

Бренды по названию

Популярные бренды