Siemens HiPath 1100 Скачать руководство пользователя страница 64

Страница: 64 / 241

Step by step

Programming an extension

Time in a UCD queue

This setting specifies the maximum length of time a call

is allowed to remain in a UCD queue.

Once the time expires, the call is disconnected or for-

warded to a UCD overflow call extension. The default

setting for a call to remain in a queue is 1 minute.

Required:

Programming mode must be activated (*95

31994).

dge

Enter the programming code.

Enter the UCD subscriber group number (790 to 799).

dd . mm

Enter the time allowed for a call to remain in a queue (00

to 99 in cycles of 5 seconds) where 00 = 0 seconds...

06 = 30 seconds... 12 = 1 minute (default), 99 = 8 min-

utes, 15 seconds.

Enter the next UCD subscriber group number.

Press this key.

Initial status for programming mode.

Waiting message before signaling a UCD call

This feature allows you to connect a call waiting mes-

sage for incoming calls before they ring at a UCD exten-

sion.

Required:

Programming mode must be activated (*95

31994).

dgf

Enter the programming code.

Enter the UCD subscriber group number (790 to 799).

Activate/Disable call waiting message:

= Activated

= Deactivated (default)

Enter the next UCD subscriber group number.

Press this key.

Initial status for programming mode.

Содержание HiPath 1100


















































































































































































































































Результаты поиска

Содержание HiPath 1100

Отзывы:

Похожие инструкции для HiPath 1100

Бренды по названию

Популярные бренды

Siemens HiPath 1100, Руководство по программированию

Результаты поиска

Содержание HiPath 1100

Отзывы:

Похожие инструкции для HiPath 1100

Бренды по названию

Популярные бренды