Siemens HiPath 1100 Скачать руководство пользователя страница 229

Страница: 229 / 241

Setup and Installation

229

Model S30817-Q936-C282

2.1 Settings

•

ON: Works as a pager

OFF: Works as an entrance telephone.

•

ON: Deactivates the timeout for paging.

OFF: Activates a 15-second timeout for paging.

•

Not used

Aspects to Consider

• The length of the cables between the X2 connector and the PABX must

not exceed 32.8 feet.

• For information on the length of wiring between the X6 connector and

the entrance telephone (at the street) see the manufacturer’s specifi-

cations. This interface supports HDL’s brand entrance telephones

(F5AZ, F8AZ and F9AZ).

• In Pager Mode the X4 connector is connected to an audio output, and

the X5 connector to an audio input.

• For more details see the Service Manual.

Содержание HiPath 1100


















































































































































































































































Результаты поиска

Содержание HiPath 1100

Отзывы:

Похожие инструкции для HiPath 1100

Бренды по названию

Популярные бренды

Siemens HiPath 1100, Руководство по программированию

Результаты поиска

Содержание HiPath 1100

Отзывы:

Похожие инструкции для HiPath 1100

Бренды по названию

Популярные бренды