Siemens HiPath 1100 Скачать руководство пользователя страница 121

Страница: 121 / 241

General settings

121

Step by step

To perform the required programming, proceed as if the

remote telephone were connected directly to the sys-

tem.

With a Fax/DID facility

If the system is equipped with a Fax/DID module pro-

grammed as an external line DID.

qmi

Enter the code using a remote MF telephone after the

call is answered.

The remote programmer must now enter the system

password using an MF telephone (default - 31994).

Wait for a confirmation tone to indicate that the pass-

word was accepted.

To perform the required programming, proceed as if the

remote telephone were connected directly to the sys-

tem.

Ending remote administration

Required:

The remote telephone is in programming

mode.

emj

Enter the programming code using the remote MF tele-

phone. This allows the system to free the external line

and the MF code receiver.

Replace the handset.

Type of MSN signal

This setting lets you choose one of the four types of

rings for various calls, and a ring for registered MSNs.

The default configuration for MSNs is Ring type 1.

Required:

Programming mode must be activated (*95

31994).

dkg

Enter the programming code.

If the system is connected through a serial cable

to a PC with access to the telephone system, the

programming can also be made using a modem

in conjunction with the HiPath 1100 Manager.

Refer to the instructions provided in the Help file.

Содержание HiPath 1100


















































































































































































































































Результаты поиска

Содержание HiPath 1100

Отзывы:

Похожие инструкции для HiPath 1100

Бренды по названию

Популярные бренды

Siemens HiPath 1100, Руководство по программированию

Результаты поиска

Содержание HiPath 1100

Отзывы:

Похожие инструкции для HiPath 1100

Бренды по названию

Популярные бренды