Siemens 6GK1411-1AC00 Скачать руководство пользователя страница 33

Страница: 33 / 150

Installation, wiring, commissioning

3.1 Important notes on using the device

SIMATIC CC7
Operating Instructions, 10/2019, C79000-G8976-C503-02

WARNING

Take measures to prevent transient voltage surges of more than 40% of the rated voltage.

This is the case if you only operate devices with SELV (safety extra-low voltage).

WARNING

LAN connection (Local Area Network)
A LAN or LAN segment with all the interconnected devices should be contained completely

in a single low voltage power distribution system in a building. The LAN is designed either

for “Environment A” according to IEEE802.3 or "Environment 0" according to IEC TR

62102.
Do not connect any electrical connectors directly to the telephone network (Telephone

Network Voltage) or a WAN (Wide Area Network).

WARNING

EXPLOSION HAZARD
Do not press the SET button if there is a potentially explosive atmosphere.

3.1.3

General notices on use in hazardous areas according to UL HazLoc / FM

This equipment is suitable for use in Class I, Division 2, Groups A, B, C and D or non-

hazardous locations only.
This equipment is suitable for use in Class I, Zone 2, Group IIC or non-hazardous locations

only.

WARNING

EXPLOSION HAZARD
You may only connect or disconnect cables carrying electricity when the power supply is

switched off or when the device is in an area without inflammable gas concentrations.

WARNING

Do not remove or replace while circuit is live when a flammable or combustible atmosphere

is present.

Содержание 6GK1411-1AC00























































































































































Результаты поиска

Содержание 6GK1411-1AC00

Отзывы:

Похожие инструкции для 6GK1411-1AC00

Бренды по названию

Популярные бренды

Siemens 6GK1411-1AC00, Руководство по эксплуатации

Результаты поиска

Содержание 6GK1411-1AC00

Отзывы:

Похожие инструкции для 6GK1411-1AC00

Бренды по названию

Популярные бренды