Siemens 6GK1411-1AC00 Скачать руководство пользователя страница 45

Страница: 45 / 150

Installation, wiring, commissioning

3.4 Commissioning

SIMATIC CC7
Operating Instructions, 10/2019, C79000-G8976-C503-02

The CLP is supplied with power by the gateway. The CLP retains all data permanently when

the power is turned off.

Note
Using brand-new CLPs
Only use a brand-new CLP or a CLP that was formatted by a gateway. The status of a

plugged CLP is displayed on the WBM page "Info".
If you are using a brand-new CLP, follow the steps below:
1.

Insert the CLP into the turned-off gateway.

Switch on the power of the gateway.

Format the CLP.
See section Saving (Page 116) for more on this.

The configuration data of the gateway is written to the CLP the next time the voltage is

switch off and on or after clicking on the "Apply" button.

Startup of the gateway with configuration file on CLP

When a configuration file is saved on the CLP and you insert the CLP into a gateway, the

gateway starts up with the configuration data of the CLP.
By inserting a CLP with valid configuration data into a brand-new gateway or a gateway that

was reset to factory settings, you can cause the gateway to start up with the configuration file

saved on the CLP.

Function

The configuration of the gateway is automatically saved on the CLP when you apply the

configuration in the WBM.
A device with an inserted CLP automatically uses the configuration data of the inserted CLP

when it starts up. This is, however, only possible when the data was written by a compatible

device type.
This allows fast and simple replacement of the basic device. If a device is replaced, the CLP

is taken from the failed device and inserted in the replacement. As soon as it starts up, the

replacement automatically applies the same device configuration as the failed device.

Inserting the CLP and startup behavior

Note
Insert and remove only when power is off
The CLP may be inserted or removed only when the power is off!

The slot for the CLP is located on the back of the device, see section CLP Slot (Page 29).

Содержание 6GK1411-1AC00























































































































































Результаты поиска

Содержание 6GK1411-1AC00

Отзывы:

Похожие инструкции для 6GK1411-1AC00

Бренды по названию

Популярные бренды

Siemens 6GK1411-1AC00, Руководство по эксплуатации

Результаты поиска

Содержание 6GK1411-1AC00

Отзывы:

Похожие инструкции для 6GK1411-1AC00

Бренды по названию

Популярные бренды