SEW-Eurodrive IPOS plus Скачать руководство пользователя страница 55

Страница: 55 / 384

Manual – IPOSplus®

Encoder combinations

Position Detection and Positioning

Direct position control with absolute encoder and motor encoder

474542091

•

Direct position control in IPOS

plus®

by means of the SSI

absolute encoder connected via DIP11.

•

An incremental encoder / resolver / Hiperface

(X15) is

always required on the motor for speed feedback.

•

Slip or mechanical play (gear unit backlash) between the
incremental encoder /resolver / Hiperface

of the motor and

the absolute encoder is compensated automatically.

•

In IPOS

plus®

, positioning commands, for example, "GOA ..."

are performed with reference to the actual source position
(here, absolute encoder DIP).

•

The dynamic response that can be achieved depends on the
properties and the installation of the absolute encoder as well
as the position resolution.

•

refer to the manual "Positioning with Absolute Encoder
DIP11A"

max

= maximum speed

max

maximum

acceleration

= Profile generator

= Position controller

act

= Actual speed

= Speed controller

ABS = absolute encoder
IPOS = IPOS

plus®

program

max

act

DIP

ABS

IPOS

Position control with incremental encoder on the motor,
Processing the absolute encoder position in the IPOS

plus

program

474543627

•

Position control is performed in IPOS

plus®

using the motor

encoder connected to X15.

•

An incremental encoder / resolver is always required on the
motor for speed feedback.

•

The high dynamic response of the inverter can be used
directly for positioning.

•

The position information of the absolute encoder is mapped
automatically in an IPOS

plus®

variable and can be processed

using program control.

•

Using the DIP11 in this way means that reference travel is
unnecessary.

•

refer to the manual "Positioning with Absolute Encoder DIP11"

max

= maximum speed

max

maximum

acceleration

= Profile generator

act

= Actual position of the motor encoder

= Position controller

act

= Actual speed

= Speed controller

ABS = absolute encoder
SV

= System variable

IPOS = IPOS

plus®

program

max

act

DIP

ABS

act

kVA

Содержание IPOS plus

































































































































































































































































































































































































Результаты поиска

Содержание IPOS plus

Отзывы:

Бренды по названию

Популярные бренды

SEW-Eurodrive IPOS plus, Руководство пользователя

Результаты поиска

Содержание IPOS plus

Отзывы:

Бренды по названию

Популярные бренды