SciCan STATIM 2000S Скачать руководство пользователя страница 46 | Manualshive

Страница: 46 / 59

SciCan STATIM 2000S Скачать руководство пользователя страница 46

10. Statim 5000 Trouble-shooting – Cycle Faults

44

Cycle Fault #13

N/A

Cycle Fault #14

Software Revisions
R1xx or R2xx only

The steam generator temperature is above 171°C
during the sterilization phase of a cycle.

This may be the result of a blocked steam generator
inlet tube, a failed or weak water pump, a failed pump or
steam generator triac, faulty seal installation or failed
solenoid valve.

Cycle Fault #15

The cassette temperature raised above the high
threshold during the Sterilization phase of a cycle or
above 138.6°C during conditioning or pressurizing
phase of the cycle

Probable causes are a blocked duct in the cassette, a
pinched exhaust tube leading to the waste bottle, or a
faulty solenoid valve.

Cycle Fault #16

The steam generator temperature went above a
threshold value.

This may be the result of a blocked steam generator
inlet tube, a failed or weak water pump, a failed pump
triac, failed steam generator triac, faulty seal installation
or failed solenoid valve.

Cycle Fault #17-
#18

N/A

Cycle Fault #19

For software rev. R1xx, R2xx and R4xx the steam
generator calibration is invalid. For software rev.
R5xx and R6xx the validation thermocouple
calibration is invalid. In both cases a new steam
generator or validation thermocouple calibration is
required.

This occurs when a new controller board or
microprocessor has been installed. This may also
happen when the unit has been subjected to a strong
static discharge corrupting the memory. Calibrate the
boiler / validation thermocouples

Cycle Fault #20

Software Revisions
R1xx or R2xx

The pump has failed to pump water into the steam
generator during a pre-vent pump time-out. The
steam generator temperature was greater than
140°C for 3.6 seconds after the pump was activated
to pump water to cool the steam generator.

This may be the result of a blocked steam generator
inlet tube, a failed or weak water pump, a failed pump
triac or steam generator triac, faulty seal installation or
failed solenoid valve. Also may be the result of a
defective water quality sensor (insufficient water in the
reservoir)

Cycle Fault #21-
#24

N/A

«
...
44
45
46
47
48
...
»

Содержание STATIM 2000S




























































Отзывы:

Нет отзывов