SciCan STATIM 2000S Скачать руководство пользователя страница 27

Страница: 27 / 59

cycles and cycle parameters are displayed one by one on the LCD display. The
available sets of cycle parameters are listed in the chart below.

Available Cycles

Unlocked
mode

Locked mode

Keypad
Button

SOLID UNWRAPPED (N)

134

C / 3.5 min



HOLLOW UNWRAPPED (S)

134

C / 3.5 min



HOLLOW UNWRAPPED (S)

134

C / 18 min



Unwrapped

HOLLOW WRAPPED (S)

134

C / 3.5 min



HOLLOW WRAPPED (S)

134

C / 18 min



Wrapped

RUBBER / PLASTICS (S)

121

C / 15 min



RUBBER / PLASTICS (S)

121

C / 30 min



Rubber &
Plastics

AIR DRYING ONLY

60 MIN. MAXIMUM



Air Drying

2.4. Conductivity Setup

Adjust the water conductivity thresholds

CD=xx.xuS/NNN/y.yppm
L=LL.L H=HH.H G=G.GG

Screen Representation

xx.x

Water conductivity in uS (micro-Siemens)

NNN

Water conductivity in ADC (Analog to Digital converter)
counts (0…255)

y.y

Water quality in ppm (parts per million)

LL.L

Lower value threshold / No water threshold. Values lower
than this triggers “No Water” error (default 0.5uS)

HH.H

High value threshold / Water quality threshold. Values
larger than this triggers “No Water” error (default 10.0uS)

G.GG

Water conductivity circuit gain (default 1.00)

Note: Distilled water readings should be between Low and High thresholds.

The currently selected field is indicated by the flashing value on the display.

Содержание STATIM 2000S



























































Результаты поиска

Содержание STATIM 2000S

Отзывы:

SciCan STATIM 2000S, Руководство по обслуживанию, Страница: 27 / 59

Результаты поиска

Содержание STATIM 2000S

Отзывы: