Schrack Technik CX plus Series FRACXP06R- Скачать руководство пользователя страница 48

Страница: 48 / 80

“

YES

”: Resets all active alarm messages (display and alarm relay) and the

alarm memory (menu ALARM).
After confirming the setting with

“YES”

, the RESET takes place. The setting

will automatically return to

“NO”

NOTE:

The alarm messages on the display are only reset, if the respective

alarms are not active anymore. The alarm relay is only reset, if no alarm is
active anymore.

607

Display of the software version status of the device

-------

For information purposes only. No settings possible.

Software version of the device. This is shown as moving script:

xx.xx.xx

608

Setting of the expert SETUP password (PIN).

0…999

Setting of the expert SETUP password (PIN) for the SETUP menus 200,
300, 400, 500, 600, 700 and 800.

NOTE:

The SETUP menu 100 is always available even without PIN. The

SETUP menu 700 is only available with the option -MB.

609

Restart Function “First Setup”

YES/NO

“

YES

”: The function “First Setup” will be restarted immediately.

“NOTE”:

The settings and stage database will not be reset! All active

stages, except FON-stages, will be deactivated one by one according to the
switch-off interval of 1 s. The control circuit is stopped as long as function
“First Setup” is activated.

Содержание CX plus Series FRACXP06R-

















































































Результаты поиска

Содержание CX plus Series FRACXP06R-

Отзывы:

Бренды по названию

Популярные бренды

Schrack Technik CX plus Series FRACXP06R-, Руководство пользователя

Результаты поиска

Содержание CX plus Series FRACXP06R-

Отзывы:

Бренды по названию

Популярные бренды