manualshive.com logo in svg

Schrack Technik CX plus Series FRACXP06R-, Руководство пользователя

Поделиться
Скачать
Schrack Technik CX plus Series FRACXP06R- Скачать руководство пользователя страница 41

 
 

 

 

41

 

 

500

   

Settings ALARM 

  

MENU 

FUNCTION

 

RANGE

 

501 

Reset alarm manually 

Yes/No 

 

“

YES

”: Alarm messages (display and alarm relay) must be reset manually. 

In order to reset active alarms, 

keep 

the key 

 

(ESC)

 

pressed 

for 

approx. 

3 s.

 

“

NO

”:  As  soon  as  the  alarm  condition  is  no  longer  active,  the  alarm 

messages (display and alarm relay) is reset automatically. 

NOTE: 

An alarm can only  be reset manually,  if it is no longer active. The 

alarm relay cannot be reset again until no alarm is active anymore.

 

 

 

502 

THD-U limit value  

3...20 % 

 

Setting of the limit value for the THD-U monitoring. 
If the set THD-U limit value is exceeded, the alarm is signalled (display and 
alarm  relay)  after  the  set  delay  time  (SETUP/  504).  The  message 

“

HarU 

ALARM

” appears on the display. The alarm relay opens its contact.

 

If the function SETUP/503 is activated, all active stages (

“AUTO” & “FON”) 

are  switched  off  one  by  one  referring  to  the  switch-off  interval  set  under 
SETUP/523 and are locked for 30 min. The last active stage is switched off 
first, when the switch-off interval has run out after the signalling of the alarm. 
Then, the other stages are switched off one by one referring to the switch-
off interval. As all active stages have been switched off, the control stops for 
as long as the alarm is still active.

 

If the value falls below the set THD-U limit value, a still active stage switch-
off  sequence  is  cancelled.  The  already  switched-off  stages,  however, 
remain locked until the blocking time (max. 30 min) has run out. If the control 
has been stopped, this is restarted and the controller can switch the stages 
again. If the function 

“Manual reset” (SETUP/501 = NO) is deactivated, the 

alarm messages (display and alarm relay) are reset automatically after 15 
s.

 

NOTE: 

The control is stopped while the alarm is active. The stages which 

have  been  switched  off  by  the  alarm  system  are  locked  for  max.  30  min. 
Active 

“FON” stages are also switched off and blocked. Stages which have 

been switched on manually are NOT switched off. If stages are switched off 
manually, they are only locked until the discharge time is expired. 

 

 

503 

THD-U / THD-I / TEMP 2 alarm = switch off active stages 

Yes/No 

 

“

NO

”: active stages are not switched off in case of an alarm. 

“

YES

”:  If  the  configured  THD-U  or  THD-I  or  TEMP  2  limit  values  is 

exceeded, all active stages (

“AUTO” & “FON”) are switched off one by one 

referring to the switch-off interval set under SETUP/523 and are locked for 
30 min. The last active stage is switched off first, when the switch-off interval 
has  run  out  after  the  signalling  of  the  alarm.  Then,  the  other  stages  are 
switched  off  one  by  one  referring  to  the  switch-off  interval.  As  all  active 
stages have been switched off, the control stops for as long as the alarm is 
still active. 

NOTE: 

The  control  is  stopped  while  the  alarm  is  still  active.  The  stages 

which have been switched off by the alarm system are locked for max. 30 
min. Active 

“FON” stages are also switched off and blocked. Stages which 

have  been  switched  on  manually  are  NOT  switched  off.  If  stages  are 
switched  off  manually,  they  are  only  locked  until  the  discharge  time  is 
expired. 

NOTE: 

The digital input alarm can also lock the control system and initiate 

the sequential deactivation of active stages. 

 

 

504 

Delay time THD-U- and THD-I-alarm 

1...255 s 

Содержание CX plus Series FRACXP06R-

















































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды