Sakai SV400D-2 Скачать руководство пользователя страница 217

Страница: 217 / 218

9-049

HYDRAULIC SYSTEM TROUBLESHOOTING

3-5-3. Blade floating operation not possible

Check point

Cause

Check/Action

1. Control Valve

Blade ﬂoating operation is not possible

because the control valve spool does
not change.

If the control valve lever does not move,
check and clean the spool, or replace
the control valve.

3-5-4. Blade hydraulic system is overheating

Check point

Cause

Check/Action

1. Oil Level of Hydraulic Oil

Tank

Oil level in hydraulic oil tank is low.

Fill the tank until the correct oil level is
obtained.

2. Oil Cooler

Cooling efﬁciency is reduced due to

clogged oil cooler ﬁns.

Clean the oil cooler ﬁn.

3. Blade Circuit Setting

Pressure

If the circuit pressure setting is
excessively low, the relief valve is open,
causing the temperature of hydraulic oil
in circuit to rise.

Measure the blade circuit pressure. If
low, increase the relief setting pressure.

If the load is excessively heavy, the relief
valve is open, causing the temperature
of hydraulic oil in circuit to rise.

Measure the blade circuit pressure. If
high, decrease the steering load.

4. Steering Pump Suction

Filter (also used for
blade circuit)

The load of steering pump increases

due to clogged ﬁlter, causing the

temperature of hydraulic oil in circuit to
rise.

Clean or replace the suction ﬁlter.

3-5-5. Abnormal noise from blade hydraulic system

Check point

Cause

Check/Action

1. Oil Level of Hydraulic Oil

Tank

Pump suction pressure is high because
oil level of hydraulic oil tank is low,
causing cavitation in the steering system
circuit.

Fill the tank until the correct oil level is
obtained.

2. Air in the Blade Hydraulic

Circuit

Cavitation is caused by air in the circuit. Bleed the circuit and check pump inlet

hose connection and hydraulic tank
connection.

3. Hydraulic Hose Clamp

Vibrator sound of hydraulic hose is
generated because the clamp securing
the hydraulic hose is loose.

Tighten bolts of the loose hydraulic hose

clamp to the speciﬁed torque.

4. Steering Pump Suction

Filter (also used for
blade circuit)

Cavitation results at the steering pump

due to clogged ﬁlter.

Clean or replace the suction ﬁlter.

Содержание SV400D-2



























































































































































































































Результаты поиска

Содержание SV400D-2

Отзывы:

Похожие инструкции для SV400D-2

Бренды по названию

Популярные бренды

Sakai SV400D-2, Руководство по ремонту

Результаты поиска

Содержание SV400D-2

Отзывы:

Похожие инструкции для SV400D-2

Бренды по названию

Популярные бренды