Sakai SV400D-2 Скачать руководство пользователя страница 157

Страница: 157 / 218

8-009

MEASUREMENT AND INSPECTION OF VIBRATOR CIRCUIT PRESSURE

6. MEASUREMENT AND INSPECTION OF VIBRATOR CIRCUIT

PRESSURE

6-1. Measurement

Oil temperature during measurement: 50 ± 5°C
(122 ± 41°F)

①

Remove the plugs from the gauge ports (1) and

(2) that are equipped with adapters attached to
the vibrator pump. Attach the pressure gauge
through the hose

, and the connector

Gauge port: M16×2.0
Low-amplitude-side gauge port: (1)
High-amplitude-side gauge port: (2)
Pressure gauge: 0 – 34.3 MPa (0 – 4975 psi)

②

Press the parking brake switch and turn the

parking brake “ON”.

③

Start the engine. Then move the throttle lever to

the high idling position.

④

Press the vibrator switch and turn vibration “ON”.

Measure the maximum value of vibrator circuit
pressure.

NOTE: If the vehicle is subjected to vibration

for a long period while in a stopped

condition, the vibrator bearing can

get burned. Therefore, use ample

care.

⑤

After measuring, promptly turn the vibration

“OFF”.

Maximum standard vibration pressure setting

: 25.0 ± 1.0 MPa (3625 ± 145 psi)

•

•
•
•
•

SV400-2-08007

SV400-2-08019

Содержание SV400D-2



























































































































































































































Результаты поиска

Содержание SV400D-2

Отзывы:

Похожие инструкции для SV400D-2

Бренды по названию

Популярные бренды

Sakai SV400D-2, Руководство по ремонту

Результаты поиска

Содержание SV400D-2

Отзывы:

Похожие инструкции для SV400D-2

Бренды по названию

Популярные бренды