Sakai SV400D-2 Скачать руководство пользователя страница 104

Страница: 104 / 218

6-002

VIBRATORY DRUM

2. VIBRATORY DRUM

2-1. Removal and Installation of Vibratory Drum

2-1-1. Removal of vibratory drum

1) Using the steering lock bar (1), connect the front

and rear frames. Firmly secure it so that the
front and rear frames do not move.

As shown in the figure on the right, lift the rear

frame with a crane. Firmly secure the vehicle
body by placing support stands and/or wooden
blocks at the rear end of the rear frame.

Do not allow the rear wheel tires to leave

the ground. (The tires must support the
vehicle’s body weight, too.)

Rear lift weight : 2,960 kg (6,530 lbs.)

When  lifting  the  vehicle,  use  an  appropriate
hoist  of  sufficient  strength.  Confirm  that  the
surrounding area is safe, and work in a natural,
unstrained posture.
Also,  to  firmly  secure  the  vehicle  body,  use  a

support stand of sufficient strength.

SV400-2-06001

SV400-2-06002

Lift with crane

Wooden
block

Support stand

SV400-2-06002

Lift with crane

Wooden
block

Support stand

Содержание SV400D-2



























































































































































































































Результаты поиска

Содержание SV400D-2

Отзывы:

Похожие инструкции для SV400D-2

Бренды по названию

Популярные бренды

Sakai SV400D-2, Руководство по ремонту

Результаты поиска

Содержание SV400D-2

Отзывы:

Похожие инструкции для SV400D-2

Бренды по названию

Популярные бренды