Sakai SV400D-2 Скачать руководство пользователя страница 215

Страница: 215 / 218

9-047

HYDRAULIC SYSTEM TROUBLESHOOTING

3-4-3. Steering wheel backlash or play is large

Check point

Cause

Check/Action

1. Steering Column

Spline of column shaft or orbitrol is
worn.

Replace the column shaft or orbitrol.

Column shaft bearing is worn.

Replace the column shaft bearings.

2. Steering Wheel

Serration (spline) of wheel or column
shaft is worn.

Replace the wheel or column shaft.

3-4-4. Steering system is overheating

Check point

Cause

Check/Action

1. Oil Level of Hydraulic Oil

Tank

Oil level in hydraulic oil tank is low.

Fill the tank until the correct oil level is
obtained.

2. Oil Cooler

Cooling efﬁciency is reduced due to

clogged oil cooler ﬁns.

Clean the oil cooler ﬁn.

3. Steering Circuit Setting

Pressure

If the circuit pressure setting is
excessively low, the relief valve is open,
causing the temperature of hydraulic oil
in circuit to rise.

Measure the steering circuit pressure. If
low, increase the relief setting pressure.

If the load is excessively heavy, the relief
valve is open, causing the temperature
of hydraulic oil in circuit to rise.

Measure the steering circuit pressure. If
high, decrease the steering load.

4. Suction Filter for

Steering Pump

The load of steering pump increases

due to clogged ﬁlter, causing the

temperature of hydraulic oil in circuit to
rise.

Clean or replace the suction ﬁlter.

3-4-5. Abnormal noise from steering system

Check point

Cause

Check/Action

1. Oil Level of Hydraulic Oil

Tank

Pump suction pressure is high because
oil level of hydraulic oil tank is low,
causing cavitation in the steering system
circuit.

Fill the tank until the correct oil level is
obtained.

2. Air in the Steering

Hydraulic Circuit

Cavitation is caused by air in the circuit. Bleed the circuit.

3. Hydraulic Hose Clamp

Vibrator sound of hydraulic hose is
generated because the clamp securing
the hydraulic hose is loose.

Tighten bolts of the loose hydraulic hose

clamp to the speciﬁed torque.

4. Suction Filter for

Steering Pump

Cavitation results at the steering pump

due to clogged ﬁlter.

Clean or replace the suction ﬁlter.

Содержание SV400D-2



























































































































































































































Результаты поиска

Содержание SV400D-2

Отзывы:

Похожие инструкции для SV400D-2

Бренды по названию

Популярные бренды

Sakai SV400D-2, Руководство по ремонту

Результаты поиска

Содержание SV400D-2

Отзывы:

Похожие инструкции для SV400D-2

Бренды по названию

Популярные бренды