Sakai SV400D-2 Скачать руководство пользователя страница 151

Страница: 151 / 218

8-003

MEASUREMENT AND ADJUSTMENT OF PROPULSION CIRCUIT PRESSURE

2. MEASUREMENT AND ADJUSTMENT OF PROPULSION

CIRCUIT PRESSURE

2-1. Measurement

Before performing to the following operation
which mentioned

①

⑤

, confirm that the

parking brake operates properly.

Oil temperature during measurement

: 50 ± 5°C (122 ± 41°F)

①

Remove the plugs from the propulsion pump’s

gauge ports (1-5 and 1-6). Attach the pressure
gauge through the adapter

Gauge port: 9/16-18UNF
Forward-side gauge port: (1-6)
Reverse-side gauge port: (1-5)
Pressure gauge: 0 – 49 MPa (0 – 7105 psi)

②

Press the parking brake switch, turn the parking

brake “ON” and move the speed change switch
to the “Low” position.

③

Start the engine. Then move the throttle lever to

the high idling position.

④

Slowly operate the forward-reverse lever to

the side to be measured, and measure the
pressure.

⑤

After measuring, promptly return the forward-

reverse lever to “neutral.”

Maximum circuit pressure:

41.8 ± 1.0 MPa (6061± 145 psi)

•

•
•
•
•

SV400-2-08001

1-6

1-5

SV400-2-08001

1-6

1-5

Содержание SV400D-2



























































































































































































































Результаты поиска

Содержание SV400D-2

Отзывы:

Похожие инструкции для SV400D-2

Бренды по названию

Популярные бренды

Sakai SV400D-2, Руководство по ремонту

Результаты поиска

Содержание SV400D-2

Отзывы:

Похожие инструкции для SV400D-2

Бренды по названию

Популярные бренды