Sakai SV400D-2 Скачать руководство пользователя страница 112

Страница: 112 / 218

6-008

VIBRATORY DRUM

3) Remove the two bolts (24).

Remove the vibrator motor (46).
Remove the breather (21).

Use aids such as work stepladders when
working, and work with a natural, unstrained
posture.

4) Remove the sixteen bolts (16).

Attach the lifting bolts/nuts (M20×2.5) as shown

in the figure on the right.

Using a crane, lift and remove the holder (19),
damper (18) and disc (14) together.

Total of lifted parts (19, 30, 18 and 14)

: 120 kg (265 lbs.)

5) Remove the sixteen bolts (9).

Remove the sleeve (7).

•
•

•

SV400-2-06014

SV400-2-06015

Lift with crane

SV400-2-06015

Lift with crane

SV400-2-00016

Содержание SV400D-2



























































































































































































































Результаты поиска

Содержание SV400D-2

Отзывы:

Похожие инструкции для SV400D-2

Бренды по названию

Популярные бренды

Sakai SV400D-2, Руководство по ремонту

Результаты поиска

Содержание SV400D-2

Отзывы:

Похожие инструкции для SV400D-2

Бренды по названию

Популярные бренды