Sakai SV400D-2 Скачать руководство пользователя страница 124

Страница: 124 / 218

6-020

VIBRATORY DRUM

20) Attach the breather (21).

Attach the O-ring (25) to the vibrator motor (46).
Using the two bolts (24) and washers, firmly
secure it to the cover.

Attach by aligning the top side of the
vibrator motor (46) and breather (21) with
the top side of the propulsion motor.

(24) M14×40: 170 N·m (125 lbf·ft)

21) Lift the vibratory drum assembly with a crane,

and set it sideways at the position of the plug

shown in the figure on the right.

Remove the oil filler plug and level plug.

From the oil filler plug hole, add approximately

21 L (5.5 gal.) of gear oil until gear oil drips from
the level plug hole.

Attach the oil filler plug and level plug.

•

•
•

•

SV400-2-06048

SV400-2-06049

Chock block

(Oil filler plug)

10-1

(Level plug)

10-3

Vibrator motor side

SV400-2-06049

Chock block

(Oil filler plug)

10-1

(Level plug)

10-3

Vibrator motor side

Содержание SV400D-2



























































































































































































































Результаты поиска

Содержание SV400D-2

Отзывы:

Похожие инструкции для SV400D-2

Бренды по названию

Популярные бренды

Sakai SV400D-2, Руководство по ремонту

Результаты поиска

Содержание SV400D-2

Отзывы:

Похожие инструкции для SV400D-2

Бренды по названию

Популярные бренды