Sakai SV400D-2 Скачать руководство пользователя страница 183

Страница: 183 / 218

9-015

ELECTRICAL SYSTEM TROUBLESHOOTING

2-3. Propulsion

Check the following items before troubleshooting.

No fuse blew.

2-3-1. Vehicle speed does not change

Reference Fig. : 2-3

Check point

Check/Cause

Action

1. Speed Change

Solenoid

- Disconnect harness and measure resistance of coil.

Standard resistance: 5.1 Ω

- If measured resistance is abnormal, the speed change

solenoid is faulty.

Replace the speed
change solenoid.

2. Speed Change

Switch

(1) When turning starter switch ON, measure the voltage

between speed change switch pin 1 inlet L wire and chassis
ground.

Standard voltage: 12 V or more

(2) When turning speed change switch ON (High) with starter

switch ON, measure the voltage between speed change
switch pin 2 inlet LW wire and chassis ground.

Standard voltage: 12 V or more

- If above item (1) is OK and item (2) is NG, the speed change

switch is faulty.

Replace the speed
change switch.

3. Harness Connecting

Between Terminals

- Check harness between terminals for continuity.
- No continuity indicates that harness is open or poorly

connected.

Repair or replace the
harness.

2-3-2. Brake does not release

The parking brake switch is turned OFF.
The foot brake switch is turned ON (the brake pedal is not depressed).

Reference Fig. : 2-3

Check point

Check/Cause

Action

1. F-R Lever Switch

(1) When turning the forward/reverse lever to forward with the

starter switch is OFF, check the continuity between the F-R
lever switch COM terminal and NC terminal.

(2) When turning the forward/reverse lever to reverse with the

starter switch is OFF, check the continuity between the F-R
lever switch COM terminal and NC terminal.

- No continuity indicates normal condition. If any continuity is

present, the F-R lever switch is faulty.

Replace the F-R
lever switch.

2. Diode Unit

(1) When the starter switch is ON and forward/reverse lever is

at neutral position, measure the voltage between the diode
unit pin I inlet W wire and chassis ground.

(2) When the starter switch is ON and forward/reverse lever is

at neutral position, measure the voltage between the diode
unit pin H inlet GW wire and chassis ground.

- If above item (1) is OK and (2) is NG, the diode unit is faulty.

Replace the diode
unit.

•

•
•

Содержание SV400D-2



























































































































































































































Результаты поиска

Содержание SV400D-2

Отзывы:

Похожие инструкции для SV400D-2

Бренды по названию

Популярные бренды

Sakai SV400D-2, Руководство по ремонту

Результаты поиска

Содержание SV400D-2

Отзывы:

Похожие инструкции для SV400D-2

Бренды по названию

Популярные бренды