
INTEGRA/-S/-G/-GS User Manual WEB GUI
SAF Tehnika JSC
68
12)
Port status and configuration
–
STP parameters of every port:
-
RSTP state
–
Indicates RSTP state of the particular port (status mode);
allows enable or disable RSTP operation for the particular port (modify
mode);
-
Port state
–
Indicates port condition. Can be one of the following:
Disabled,
Blocking, Listening, Learning,
or
Forwarding
;
-
Role
–
the role of the particular port. Can be one of the following:
Root,
Designated, Alternate, Backup,
or
Disabled
;
-
Priority
–
Indicates Port Priority (status mode); allows specifying Port Priority
(modify mode). A combination of Priority, Port number, and Path Cost
determines whether the port will be selected as the Root port or will be
blocked on the occasion of a loop, etc;
-
Path cost
–
Indicates Path cost of the particular port (status mode); allows
specifying Path cost for the particular port by setting Path cost value or by
selecting
Auto
mode (modify mode). This parameter setting depends on the
capacity of a separate port;
-
Edge
–
displays that this particular port is Edge port;
-
Point-to-point
–
displays whether there is a point-to-point connection from
the particular port or not;
13)
Rx MSTP BPDUs
–
Indicates how many MSTP BPDUs packets were received;
14)
Rx RSTP BPDUs
–
Indicates how many RSTP BPDUs packets were received;
15)
RX Conf BPDUs
–
Indicates how many STP BPDUs packets were received;
16)
RX TCN BPDUs
–
Indicates how many topology changing notification BPDUs packets
were received;
17)
Bad MSTP BPDUs
–
Indicates how many bad MSTP BPDUs packets were received;
18)
Bad RSTP BPDUs
–
Indicates how many bad RSTP BPDUs packets were received;
19)
Bad Conf BPDUs
–
Indicates how many bad STP BPDUs packets were received;
20)
Bad TCN BPDUs
–
Indicates how many bad topology changing notifications BPDUs
packets received;
21)
Tx MSTP BPDUs
–
Indicates how many MSTP BPDUs packets were sent;
22)
Tx RSTP BPDUs
–
Indicates how many RSTP BPDUs packets were sent;
23)
Tx Conf BPDUs
–
Indicates how many STP BPDUs packets were sent;
24)
Tx TCN BPDUs
–
Indicates how many topology changing notification BPDUs packets
were sent;
25)
Fwd Transitions
–
Indicates how many times the port has been changed to forward
status;
26)
By pressing
„Execute configuration”,
changes made to the corresponding section
apply only to the local side Integra/Integra-S/Integra-G/Integra-GS. If
„Rollback on”
is
selected, the configuration will be reverted in case erroneous configuration changes
are applied.
CLI commands (
Chapter 4: COMMAND LINE INTERFACE
stp status
Use to show the status of STP configuration.
stp bridgeID
{0 | 4096 | 8192 | 12288
| 16384| 20480 | 24576 | 28672 |
32768 | 36864 | 40960 | 45056 |
49152 | 53248 | 57344 |61440}
Use to set the value of Bridge ID.
stp helloTime
<1..100>
Use to set the value of the time gap in seconds
between which the BPDU packets are being sent.
stp maxAge
<6..40>
Use to set the time period in seconds, during which
the received BPDU packets’ information is stored for a
separate port.
stp forwardDelay
<4..30>
Use to set the time period that determines the time in
seconds a separate port stays in Listening and
Learning conditions.
stp state
{enable|disable}
Use to enable or disable RSTP operation.
Содержание Integra
