
INTEGRA/-S/-G/-GS User Manual WEB GUI
SAF Tehnika JSC
62
2)
Egress rate / CIR
–
Indicates configured egress rate CIR (Committed Information
Rate) on a particular port in Mbps (status mode); allows setting egress rate CIR on a
particular port in Mbps (modify mode). The default
setting is “
1000
”
.
3)
Egress rate / CBS
–
Indicates configured egress rate CBS (Committed Burst Size) on
a particular port in kB (status mode); allows setting egress rate CBS on a particular
port in kB (modify mode). The default
setting is “
2000
”.
4)
Ingress rate / Status
–
Indicates whether ingress rate is enabled or disabled on a
particular port (status mode); allows enabling/disabling ingress rate on a particular
port (modify mode).
5)
Ingress rate / CIR
–
Indicates configured ingress rate CIR (Committed Information
Rate) on a particular port in Mbps (status mode); allows setting ingress rate CIR on a
particular port in Mbps (modify mode). The default
setting is “
1000
”.
6)
Ingress rate / CBS
–
Indicates configured ingress rate CBS (Committed Burst Size) on
a particular port in kB (status mode); allows setting ingress rate CBS on a particular
port in kB (modify mode). The default
setting is “
2000
”.
7)
By pressing
„Execute configuration”
,
changes made to the corresponding section
apply only to the local side Integra/Integra-S/Integra-G/Integra-GS. If
„Rollback on”
is
selected, the configuration will be reverted in case erroneous configuration changes
are applied.
CLI commands (
Chapter 4: COMMAND LINE INTERFACE
network port show egress-rate
<port>
Use to show egress rate limit settings and the status of a
particular port.
network port show ingress-rate
<port>
Use to show ingress rate limit settings and the status of a
particular port.
network port set
<port>
egress-
rate cir
<96
…1000000
kbps>
cbs
<64…125000
kB>
Use to set Committed Information Rate (CIR) and
Committed Burst Size (CBS) setting for egress rate limit on
a particular port.
network port set
<port>
ingress-rate cir
<96
…1000000>
cbs
<64
…
125000>
Use to set Committed Information Rate (CIR) and
Committed Burst Size (CBS) setting for ingress rate limit
on a particular port.
network port set
<port>
egress-
rate state
{enable|disable}
Use to enable or disable egress rate limiting on a particular
port.
network port set
<port>
ingress-rate state
{enable|disable}
Use to enable or disable ingress rate limiting on a
particular port.
Networking
→
Ethernet
→
MAC address table
The MAC address table displays the forwarding table of MAC addresses learned by the
switch (Dynamic) and manually entered (Static).
Содержание Integra
