rotork IQT Скачать руководство пользователя страница 77 | Manualshive

Страница: 77 / 88

background image

Refer to actuator nameplate for unit specific approval details

European – Hazardous area

EExd IIB T4. ATEX (94/9/EC) II 2GD

CENELEC Norm EN50014 and EN50018
Temperature -20°C to +70°C (-4°F to +158°F).
*Option -30°C to +70°C (-22°F to +158°F).
*Option -40°C to +70°C (-40°F to +158°F).
*Option -50°C to +40°C (- 58°F to +104°F).

EExd IIC T4. ATEX (94/9/EC) II 2GD

CENELEC Norm EN50014 and EN50018.
Temperature -20°C to +70°C (-4°F to +158°F).

EExde IIB T4. ATEX (94/9/EC) II 2GD

CENELEC Norm EN50014, EN50018 and EN50019.
Temperature -20°C to 70°C (-4°F to +158°F).
*Option -30°C to +70°C (-22°F to +158°F).
*Option -40°C to +70°C (-40°F to +158°F).
*Option -50°C to +40°C (-58°F to +104°F).

EExde IIC T4. ATEX (94/9/EC) II 2GD

CENELEC Norm EN50014, EN50018 and EN50019.
Temperature -20°C to +70°C (-4°F to +158°F).

International – Hazardous area
IEC. Exd IIB T4

IEC60079-0 and IEC60079-1 for Exd IIB T4
Temperature -20°C to +60°C (-4°F to +140°F)

IEC. Exd IIC T4

IEC60079-0 and IEC60079-1 for Exd IIC T4
Temperature -20°C to +60°C (-4°F to +140°F)

USA – hazardous Area
FM. Class 1, Division 1, Groups C, D, E, F, G hazardous areas.

Factory Mutual - Explosionproof to NEC Article 500.
Temperature -30°C to +60°C (-22°F to +140°F).
*Option -40°C to +60°C (-40°F to +40°F).
*Alternative for Group B hazardous area. Temperatures as for Groups C and D.

Canada – hazardous Area

CSA EP. Class 1, Division 1, Groups C and D hazardous areas.
Canadian Standard Association - Explosionproof
Temperature -30°C to +70°C -22°F to +158°F).
*Option -50°C to +40°C (-58°F to +104°F).
*Alternative for Group B hazardous area. Temperatures as for Groups C and D.

International Non hazardous
WT: Standard watertight, BS EN 60529 :1992, IP68, 7 metres/72 hours.

Temperature -30°C to +70°C (-22°F to +158°F).
*Option -40°C to +70°C (-40°F to +158°F).
*Option -50°C to +40°C (-58°F to +104°F).

US – Non hazardous
NEMA 4, 4X and 6.

Temperature -30°C to +70°C (-22°F to +158°F).
*Option -40°C to +70°C (-40°F to +158°F).
*Option -50°C to +40°C (-58°F to +104°F).

Canada – Non hazardous
CSA WT: Canadian Standard Association –Watertight.
Wiring and components complying with CSA Enclosure 4 and 4X.

Temperature -30°C to +70°C (-22°F to +158°F).
*Option -40°C to +70°C (-40°F to +158°F).
*Option -50°C to +40°C (-58°F to +104°F).

Rotork can supply actuators to national standards not listed above.
For details please contact Rotork.

73

IQ Approvals

12

«
...
75
76
77
78
79
...
»

Содержание IQT

























































































Отзывы:

Нет отзывов

Похожие инструкции для IQT

Бренд: Faber Страницы: 8

Concord express

Бренд: GE Страницы: 3

Бренд: Canarm Страницы: 3

Бренд: tams elektronik Страницы: 60

Бренд: Eaton Страницы: 2

Бренд: EasySMX Страницы: 11

Бренд: EasySMX Страницы: 8

Бренд: Watts Страницы: 8

Бренд: Paradox Страницы: 3

phyCORE-MCF548x

Бренд: Phytec Страницы: 104

PDS CONTROL Series

Бренд: S&P Страницы: 32

Бренд: Inkel Страницы: 12

Бренд: Gecko Страницы: 82

Бренд: Estun Страницы: 41

Elan SRB 201ZH X3

Бренд: schmersal Страницы: 6

Бренд: Zeversolar Страницы: 8

Бренд: ECUE Страницы: 39

Бренд: Regada Страницы: 41

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды