rotork IQT Скачать руководство пользователя страница 69 | Manualshive

Страница: 69 / 88

background image

H1

Phase

Position

Loss

Error

Local

Controls

Error

Battery Low

on

Power-up

Help Screen 1

POSITION ERROR

Bar ON = Current Position Error
Present.

During power up the actuator position
processor compares the current position
to that stored in the eeprom. If there is
a discrepancy this is shown as a current
position error.

Re-setting of both actuator limits
should now be carried out

(refer to

section 8)

.

BATTERY LOW ON POWER UP

Bar ON = Low battery detected On
Power Up.

If

[OS]

is selected

[O

n

]

(set as default )

the actuator operation will be inhibited
when powered up with a discharged
battery

(refer to

[OS]

page 58)

.

The battery should be replaced at the
earliest opportunity

(refer to section

10)

.

LOCAL CONTROLS ERROR

Bar ON = Invalid Local Control
Signals Detected.

For example if a Local Open and Close
signal is detected at the same time this
would be classed as an invalid or fault
condition.

PHASE LOSS

Bar ON = Phase Lost (3 Phase
Actuators Only).

Loss of third monitored power supply
phase connected to actuator terminal 3.

H2

ESD

Active

Low

Battery

Battery

Discharged

Help Screen 2

BATTERY DISCHARGED

Bar ON = Battery Discharged.

Bar ON when the battery is no longer
able to support actuator functions
under loss of power conditions.

The battery must be replaced

(refer to

Section 10)

and limit positions reset

(refer to

[LC]

and

[LO]

section 8)

.

LOW BATTERY

Bar ON = Battery level low.
Bar OFF = Battery OK.

Bar ON when the battery is low but still
able to support the necessary actuator
functions.

The battery should be replaced at the
earliest possible opportunity.

ESD SIGNAL ACTIVE

Bar ON = ESD Signal is present.

When applied, an Emergency
Shutdown Signal will override any
existing local or remote control signal,
causing the actuator to respond in the
direction selected for ESD.

The ESD function will be determined by
the settings on Control Mode
Configuration screens

[A1]

to

[A5]

(refer to Section 9.3)

.

The actuator will not respond to any
local or remote control while an ESD
signal is maintained.

65

H1

Factors Inhibiting
Electrical Operation

H2

Battery Level and
ESD Control Input

«
...
67
68
69
70
71
...
»

Содержание IQT

























































































Отзывы:

Нет отзывов

Похожие инструкции для IQT

Бренд: CAME Страницы: 32

Бренд: Babybee Prams Страницы: 21

COOPER POWER SERIES

Бренд: Eaton Страницы: 50

Бренд: Fagor Страницы: 10

Бренд: Fagor Страницы: 358

Бренд: Fagor Страницы: 556

Бренд: Fagor Страницы: 172

Бренд: Fagor Страницы: 180

Бренд: Fagor Страницы: 112

Master Control Unit

Бренд: FaderMate Страницы: 36

Бренд: KEENZ Страницы: 68

Бренд: Vacon Страницы: 132

AMES 4000SS Series

Бренд: Watts Страницы: 8

Бренд: Monster Central Страницы: 13

Бренд: Rain Bird Страницы: 18

Бренд: ICP DAS USA Страницы: 4

InRAX MVI46-PDPS

Бренд: ProSoft Technology Страницы: 72

Бренд: Patton Страницы: 56

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды