rotork IQT Скачать руководство пользователя страница 70

Страница: 70 / 88

Clockwise

Limit

Anti
Clockwise
Limit

Inhibit

Help Screen 3

CLOCKWISE LIMIT

Bar ON = Actuator has reached
clockwise limit of travel.

ANTI-CLOCKWISE LIMIT

Bar ON = Actuator has reached
Anti-clockwise limit.

INHIBIT

Bar ON = Actuator inhibited.

Possible Causes:

Phase Loss (3 phase only).
Power Loss Inhibit (page 58).
Internal Failure.

Remote

Maintain 2

Open 1

ESD 2

Remote
Close 1

Remote

Close 2

ESD 1

Remote

Open 2

Maintain 1

Help Screen 4

All remote signals designated with ‘1’
are standard hard wired remote inputs.

When a Pakscan, Profibus or
Foundation Fieldbus card is fitted,
remote control inputs are designated
with a ‘2’.

REMOTE OPEN 1

Bar OFF = Remote Open Signal
Present

REMOTE CLOSE 1

Bar OFF = Remote Close Signal
Present.
ESD 1
Bar OFF = ESD signal present.

REMOTE MAINTAIN 1

Bar OFF = Remote Maintain
signal present.
Bar ON = Remote Maintain not
present and/or Remote Stop
active.

REMOTE OPEN 2

Bar OFF = Remote Open signal
present from BUS option pcb.

REMOTE CLOSE 2

Bar OFF = Remote Close signal
present from BUS option pcb.

ESD 2

Bar OFF = ESD signal present
from BUS option pcb.

REMOTE MAINTAIN 2

Bar OFF = Remote Maintain
signal present from BUS option
pcb.

Local Stop

not

Open

Selected

Interlock

Thermostat

Tripped

Interlock

Local Open

Local not

not Present

Selected

Local Close

Remote

not

Present

Selected

Help Screen 5

OPEN INTERLOCK

Bar ON = Open Interlock Active.

(Actutator disabled)

Unauthorised Open electrical operation
can be prevented by interlocking the
actuator (Open) control with an
external interlock contact.

If external interlocks are not required
the interlock function must be selected
OFF.

Factors Inhibiting
Electrical Operation

Remote Control
Inputs

Remote Interlocks,

Local Control

Inputs, & T/stat

Содержание IQT

























































































Результаты поиска

Содержание IQT

Отзывы:

Похожие инструкции для IQT

Бренды по названию

Популярные бренды

rotork IQT, Инструкция по установке и обслуживанию

Результаты поиска

Содержание IQT

Отзывы:

Похожие инструкции для IQT

Бренды по названию

Популярные бренды