rotork IQT Скачать руководство пользователя страница 51

Страница: 51 / 88

Setting instructions for actuators
including an optional Profibus DP
module – check wiring diagram for
inclusion.

Before setting the parameters for
Option Profibus ensure Remote
Control Source [Od] has been
selected to [oP] in Section 9.7.

Profibus module set-up screens can be
turned off to provide extra security. The
action of turning screens on or off does
not affect its operation.

Use the

keys to turn on Profibus

set-up screens.

Profibus set-up screens

]

PRESS THE

KEY.

The displayed option will flash
indicating that it has been set.

Press the

key to display the Profibus

set-up screens.

The Profibus DP module must be
allocated a unique address.

To set the address the Profibus module
must be isolated from the host by
disconnecting the RS485 highway or
turning off the host device.

Using the

keys display the

required address.

Address to be set within the range 01
to 7E Hexadecimal

(refer to page 72 for

conversion)

. If an address value outside

this range is entered, the address set
will revert to 01 (for 00) or 7E (for value
above 7E).

PRESS THE

KEY.

The displayed option will flash
indicating that it has been set.

Press the

to display

[Pb]

9.10

Bus System
Option Profibus DP [OP]

Profibus Address

Содержание IQT

























































































Результаты поиска

Содержание IQT

Отзывы:

Похожие инструкции для IQT

Бренды по названию

Популярные бренды

rotork IQT, Инструкция по установке и обслуживанию

Результаты поиска

Содержание IQT

Отзывы:

Похожие инструкции для IQT

Бренды по названию

Популярные бренды