rotork IQT Скачать руководство пользователя страница 3 | Manualshive

Страница: 3 / 88

background image

This manual covers IQT range actuators:

* IQT - Operation of isolating/regulating 1/4 turn valves.
* IQTM - Operation of modulating 1/4 turn valves.
* IQTF - Operation of part-turn and slow speed multi-turn

valves.

It provides instruction on:

* Manual and electrical (local and remote) operation.

* Preparation and installation of the actuator onto the

valve.

* Commissioning and adjustment of the

Primary Settings for correct valve operation.

* Commissioning and adjustment of the Secondary

Settings to suit site-specific control and indication

requirements.

* Maintenance – Troubleshooting.

* Sales and Service.

Refer to Publication E185E for repair, overhaul and
spare part instructions.

THE ROTORK IQT RANGE – THE FIRST

1

/

4

TURN VALVE ACTUATOR

THAT YOU CAN COMMISSION AND INTERROGATE WITHOUT
REMOVING ELECTRICAL COVERS.

Using the supplied infra-red Setting Tool to access the actuator set up
procedures, “point and shoot” setting of torque levels, position limits and
all other control and indication functions can be made safely, quickly and
conveniently, even in hazardous locations. The IQT allows commissioning
and adjustment to be carried out with the main power supply to the
actuator switched on or off.

Standard diagnostics access information about the control system, valve
and actuator status in the form of display icons and help screens.

Instantaneous valve torque and position can be monitored on the actuator
with a single key press of the Setting Tool.

The on board Datalogger captures operational and valve torque data
enabling informed maintenance choices to be made. IQ Insight software
for PC allows the Datalogger to be interrogated, as well as the complete
actuator set up to be configured and recorded.

The actuator containing the Setting Tool will be identified with a yellow
label on the terminal cover.

Visit our web site at

www.rotork.com

for more information on the IQT and

other Rotork actuator ranges.

«
1
2
3
4
5
...
»

Содержание IQT

























































































Отзывы:

Нет отзывов

Похожие инструкции для IQT

Бренд: Vacon Страницы: 62

Leroy-Somer R180

Бренд: Nidec Страницы: 20

Бренд: D-Link Страницы: 113

Бренд: D-Link Страницы: 146

Бренд: Mamas & Papas Страницы: 16

Бренд: Galcon Страницы: 32

Бренд: Barthelme Страницы: 8

Бренд: CAB Страницы: 28

Бренд: C-TEC Страницы: 16

Бренд: C&T Solution Страницы: 27

SECURIT ST800L+

Бренд: C&K systems Страницы: 16

Бренд: Rane Страницы: 2

Бренд: Eaton Страницы: 448

Бренд: Eaton Страницы: 57

Бренд: Mitsubishi Страницы: 30

SmarTemp Control fx

Бренд: Webasto Страницы: 8

Бренд: Cypress Страницы: 2

Бренд: Dudley Страницы: 8

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды