rotork IQT Скачать руководство пользователя страница 37

Страница: 37 / 88

Extra indication contacts S5

[r5]

, S6

[r6]

, S7

[r7]

and S8

[r8]

are available as

an option.

Check actuator circuit diagram for
inclusion.

When the Extra Contact Option is
included the set-up procedure and
available contact functions for S5 – S8
are identical to S1–S4

(refer to Section

9.2 page 28)

Unless specified with order the default
setting for the extra indication contacts
will be as follows:

[r5]

Close limit indication

[r6]

Open limit indication

[r7]

Torque trip mid travel

[r8]

Remote control selected

NOTE:

If the Extra Contact Option is

not included in the actuator build, any
settings made for S5–S8 will have no
effect on the indication output of the
actuator.

The action of turning on the Extra
Contact Option makes an additional
series of set-up screens available

Enabled Disabled

Extra Contact Set-up Displays

Press the

key to select the Extra

Contact Option set-up screens

]

PRESS THE

KEY.

The displayed option will flash
indicating that it has been set.

PRESS THE

KEY TO ACCESS S5

TO S8 SET-UP DISPLAYS.

The procedure for setting S5 to S8
is the same as that for S1 to S4

(refer to Section 9.2 page 28)

9.4

Option Extra
Indication Contacts

Display Extra Contact
Set-up Screens

Содержание IQT

























































































Результаты поиска

Содержание IQT

Отзывы:

Похожие инструкции для IQT

Бренды по названию

Популярные бренды

rotork IQT, Инструкция по установке и обслуживанию

Результаты поиска

Содержание IQT

Отзывы:

Похожие инструкции для IQT

Бренды по названию

Популярные бренды