rotork IQT Скачать руководство пользователя страница 60

Страница: 60 / 88

Setting instructions for actuator
including an interrupter timer.

The interrupter timer enables pulsed
“stop/start” operation by the actuator
as a response to local and remote
control commands.

This effectively increases the valve
stroke time and can be adjusted to
prevent hydraulic shock (water
hammer) and flow surges in pipelines.

The interrupter timer is an optional
extra – check wiring diagram for
inclusion.

When fitted, the timer will be
made available for operation.

The Interrupter cannot be
enabled or disabled using the
Setting Tool.

Interrupter Timer Interrupter Timer

Disabled Enabled

When the timer option is available an
additional series of settings can be
accessed by pressing the

key.

NOTE:

If the timer option is not

available pressing the

key will not

access setting.

Press the

key to display interrupter

timer set-up screens.

The default for timer direction is

[CL]

timer operation will

start in closing

and

stop in opening

– pulsing

operation around the close position.

If pulsing operation is required to stop
in closing and start in opening – around
the open position, use the

key.

The display will change to

[OP]

PRESS THE

KEY.

The displayed option will flash
indicating that it has been set.

Pulsed Operation Around the

Closed Position

NOTE: Instructions

[JC]

and

[JO]

are for

timer operation around the Closed
position. For timing around the Open
position, read stop for start

[JC]

and

start for stop

[JO]

Press the

key to display

[JC]

Using the

key select the position

for the

TIMER TO START WHEN THE

VALVE IS CLOSING.

[

] [

]

= valve closed

[01]

[99]

= percentage open

[

]

= valve open

Timer Set to Start Pulsing when

Closing Valve Reaches 25% Open

PRESS THE

KEY.

The displayed option will flash
indicating that it has been set.

If the timing is not required in the
closing stroke select

[JC]

[

] [

]

valve

closed position.

Press the

key to display

[JO]

9.13

Option
Interrupter Timer

Interrupter Timer
Enabled/Disabled

9.13

Interrupter Timer
Direction

9.13

Position in Valve

Closing Stroke for

Timer to Start

Содержание IQT

























































































Результаты поиска

Содержание IQT

Отзывы:

Похожие инструкции для IQT

Бренды по названию

Популярные бренды

rotork IQT, Инструкция по установке и обслуживанию

Результаты поиска

Содержание IQT

Отзывы:

Похожие инструкции для IQT

Бренды по названию

Популярные бренды