Roland Juno-Stage, Руководство пользователя

Страница: 169 / 256

169
Effects List
A phaser that continues raising/lowering the frequency at which the
sound is modulated.
fig.MFX-14
This is an effect that applies amplitude modulation (AM) to the input
signal, producing bell-like sounds. You can also change the
modulation frequency in response to changes in the volume of the
sound sent into the effect.
fig.MFX-15
This is a ring modulator that uses a 16-step sequence to vary the
frequency at which modulation is applied.
fig.MFX-16
You can use multi-effect control to make the step sequence play
again from the beginning (p. 164).
Cyclically modulates the volume to add tremolo effect to the sound.
fig.MFX-17a
14: INFINITE PHASER
Parameter Value Explanation
Mode 1, 2, 3, 4
Higher values will produce a
deeper phaser effect.
Speed # -100–+100
Speed at which to raise or lower
the frequency at which the sound
is modulated
(+: upward / -: downward)
Resonance # 0–127 Amount of feedback
Mix # 0–127
Volume of the phase-shifted
sound
Pan # L64–63R Panning of the output sound
Low Gain -15–+15 dB
Amount of boost/cut for the
low-frequency range
High Gain -15–+15 dB
Amount of boost/cut for the
high-frequency range
Level 0–127 Output volume
15: RING MODULATOR
Parameter Value Explanation
Frequency # 0–127
Adjusts the frequency at which modulation is
applied.
Sens # 0–127
Adjusts the amount of frequency modulation
applied.
Polarity UP, DOWN
Determines whether the frequency
modulation moves towards higher
frequencies (
UP ) or lower frequencies
( DOWN ).
Low Gain -15–+15 dB Gain of the low frequency range
High Gain -15–+15 dB Gain of the high frequency range
Balance #
D100:0W–
D0:100W Volume balance between the direct sound
(D) and the effect sound (W)
Level 0–127 Output level
Infinite Phaser 2-Band EQ
L in
R in
L out
R out
Pan R
Pan L
L in
R in
L out
R out
Ring Mod
2-Band EQ
2-Band EQ
Ring Mod
16: STEP RING MODULATOR
Parameter Value Explanation
Step 01–16 0–127
Frequency of ring modulation at
each step
Rate # 0.05–10.00 Hz, note
Rate at which the 16-step sequence
will cycle
Attack # 0–127
Speed at which the modulation
frequency changes between steps
Low Gain -15–+15 dB
Amount of boost/cut for the
low-frequency range
High Gain -15–+15 dB
Amount of boost/cut for the
high-frequency range
Balance # D100:0W–D0:100W
Volume balance of the original
sound (D) and effect sound (W)
Level 0–127 Output volume
17: TREMOLO
Parameter Value Explanation
Mod Wave
TRI, SQR, SIN, SAW1,
SAW2
Modulation Wave
TRI: triangle wave
SQR: square wave
SIN: sine wave
SAW1/2: sawtooth wave
Rate #
0.05–10.00 Hz, note Frequency of the change
Depth # 0–127 Depth to which the effect is applied
Low Gain -15–+15 dB Gain of the low range
High Gain -15–+15 dB Gain of the high range
Level
0–127 Output Level
L in
R in
L out
R out
Step Ring Mod
2-Band EQ
2-Band EQ
Step Ring Mod
L in
R in
L out
R out
Tremolo
2-Band EQ
2-Band EQ
Tremolo
SAW1 SAW2
JUNO-STAGE_e.book 169 ページ ２００８年１０月１７日 金曜日 午後１２時２７分