Roland Juno-Stage, Руководство пользователя

Страница: 110 / 256

110
Chapter 8. Detailed Editing for Patches
MATRIX CTRL1–4
The function which allows you use MIDI messages to make changes in realtime to the tone parameters is called the Matrix Control . Up to four Matrix
Controls can be used in a single patch.
To use the Matrix Control, specify which MIDI message (CTRL Source) will be used to control which parameter (CTRL Destination), and how greatly
(CTRL Sens), and the tone to which the effect is applied (CTRL Switch).
VELOCITY and KEY FOLLOW correspond to Note messages.
• Although there are no MIDI messages for LFO 1 through TVA Envelope, they can be used as Matrix Control. In this case, you can change the
tone settings in realtime by playing patches.
• If you want to use common controllers for the entire JUNO-STAGE, select “SYS CTRL1”–”SYS CTRL4.” MIDI messages used as System Control 1–
4 are set with the System Ctrl 1–4 Source parameters (p. 148).
• If Rx Bender, Rx Expression, or Rx Hold-1 (p. 112) are “ON,” incoming MIDI messages of these types will affect the Pitch Bend, Expression, or
Hold 1 settings at the same time that they affect the target parameter (CTRL Destination). If you want these incoming messages to affect only the
target parameter, turn these settings “OFF.”
• There are parameters that let you specify whether specific MIDI messages will be received for each channel in a performance (p. 138). When a
patch with Matrix Control settings is assigned to a part, confirm that any MIDI messages used for the Matrix Control will be received. If the
JUNO-STAGE is set up such that reception of MIDI messages is disabled, then the Matrix Control will not function.
Matrix Control Settings/Miscellaneous Settings
Parameter Value Explanation
CTRL 1–4 Source
OFF,
CC01–31, 33–95,
PITCH BEND,
AFTERTOUCH,
SYS CTRL1–4,
VELOCITY,
KEY FOLLOW,
TEMPO, LFO1,
LFO2, PITCH ENV,
TVF ENV, TVA ENV
MIDI message used to change the tone parameter with the Matrix Control
OFF: Matrix control will not be used.
CC01–31, 33–95: Controller numbers 1–31, 33–95
PITCH BEND: Pitch Bend
AFTERTOUCH: Aftertouch
SYS CTRL1–4: Controllers that are shared by the entire JUNO-STAGE (see TIP below)
VELOCITY: Pressure you press a key with
KEY FOLLOW: Keyboard position with C4 as 0
TEMPO: The specified tempo of the JUNO-STAGE or the tempo of an external MIDI sequencer.
LFO1: LFO 1
LFO2: LFO 2
PITCH ENV: Pitch envelope
TVF ENV: TVF envelope
TVA ENV: TVA envelope
Parameter Value Explanation
CTRL 1–4
Destination 1–4
OFF, PITCH, CUTOFF,
RESONANCE, LEVEL,
PAN, OUTPUT LEVEL,
CHORUS SEND,
REVERB SEND,
LFO1/2 PITCH DEPTH,
LFO1/2 TVF DEPTH,
LFO1/2 TVA DEPTH,
LFO1/2 PAN DEPTH,
LFO1/2 RATE,
PCH ENV A-TIME,
PCH ENV D-TIME,
PCH ENV R-TIME,
TVF ENV A-TIME,
TVF ENV D-TIME,
TVF ENV R-TIME,
TVA ENV A-TIME,
TVA ENV D-TIME,
TVA ENV R-TIME, TMT,
FXM DEPTH,
MFX CTRL1–4
Tone parameters that are to be controlled when using the Matrix Control
Up to four parameters can be specified for each Matrix Control, and controlled simultaneously.
* In this manual, parameters that can be controlled using the Matrix Control are marked with a
“
★
.”
JUNO-STAGE_e.book 110 ページ ２００８年１０月１７日 金曜日 午後１２時２７分