Robomow City 120 Скачать руководство пользователя

Страница: 5 / 76

Introduction - 3

Introduction

Warning Decal Definitions

These are the symbols on Robomow



; Read them carefully before operating Robomow



DANGER! Sharp rotating blades. Keep hands and feet away.

Serious injury can occur. Caution – Do not touch rotating blade(s)

CAUTION!

Remove Power Pack before

attempting to lift the mower for any reason.

1. Safety alerts symbol – WARNING -

this is a dangerous power tool. Use care when operating and follow all safety

instructions and warnings.

2. Read operator’s manual –

Read user instructions before operating your Robomow



3. Hazard of Thrown or flying objects -

Whole body exposure, take caution.

4. Keep a safe distance from the machine when operating

Keep people in particular children, pets and bystanders away from the area in which Robomow is being used.

5. Severing of toes or fingers - Rotary mower blade

Risk of injury from rotating cutting blade. Keep hands and feet away and do not attempt to lift Robomow from

this area.

6. Remove the disabling device before working on or lifting Robomow



Remove the Power Pack before working on or

lifting Robomow



7. Do not ride on Robomow



Do not dispose Robomow



or any other part of it as unsorted

municipal waste – it should be collected separately.

This warning symbol will be found at several

points throughout the pages of this manual.

It is intended to highlight an important safety,

warning or cautionary message.

Please pay particular attention to these

areas and be sure you fully understand

the message before proceeding.

1 2 3 4 5 6 7

WARNING!

Содержание City 120













































































Результаты поиска

Содержание City 120

Отзывы:

Похожие инструкции для City 120

Бренды по названию

Популярные бренды

Robomow City 120, Инструкция по эксплуатации и безопасности

Результаты поиска

Содержание City 120

Отзывы:

Похожие инструкции для City 120

Бренды по названию

Популярные бренды