Robomow City 120 Скачать руководство пользователя

Страница: 71 / 76

Chapter 10-4

Maintenance and Storage

10.8 Maintenance of the Base Station area

Keep the Base Station entrance and area clean of leaves, sticks, twigs

or any other debris that usually accumulate in such areas.

NEVER

spray a water hose directly on the Base Station.

Always use a damp cloth and brush to clean the surface and area

under the charging cover (where the contacts are).

Be careful when trimming around the Base Station with a powered

weed trimmer as damage to the surface or power cord may occur.

Treat any insect mounds with a locally recommended insecticide.

In the event of damage to any part of the power cord, stop use of the

Base Station, disconnect the power supply and replace the power cord.

10.9 Winter Storage

10.9.1 Storing the Power Pack

Fully charge the Power Pack.

Separate the Power Pack from Robomow for storing.

Store the Power Pack off the ground in a cool, dry place.

Temperature should not be colder than -4 ºF (-20 ºC).

Charge the Power Pack before using the Robomow for the first time

next season.

It is recommended to fully charge the battery every three months while

not in use.

10.9.2 Storing Robomow

Remove the Power Pack and clean Robomow

Store Robomow in a clean dry place.

Cover it to keep it clean and protected.

Store Robomow standing on its wheels with a free space around the

bumpers.

IMPORTANT

Do not store Robomow on its bumpers. Make sure

nothing else presses against the bumpers.

Check the condition of the blades.

If necessary, replace the blades.

Содержание City 120













































































Результаты поиска

Содержание City 120

Отзывы:

Похожие инструкции для City 120

Бренды по названию

Популярные бренды

Robomow City 120, Инструкция по эксплуатации и безопасности

Результаты поиска

Содержание City 120

Отзывы:

Похожие инструкции для City 120

Бренды по названию

Популярные бренды