Robomow City 120 Скачать руководство пользователя

Страница: 62 / 76

Chapter 8-4

Robomow City 120

Message Displayed

Probable Cause/Event

Corrective/User Action

- The mowing motors have been working under

a severe load for too long of a time.

- There is no need to do anything – Robomow will

renew automatically the operation, as the mowing

motor will cool down.

Mowing Overload

Cooling Wait

- Perimeter Switch is not turned on or not

connected to the zone intended to mow

- Make sure the Perimeter Switch is connected to the

correct zone and is turned on

No Wire Signal

- Robomow detects rain upon GO pressing

- Do not operate Robomow in rainy weather and

wet grass; If you choose to override, press the

GO button; The overriding is valid for the current

operation only

Rain detected Go to

ignore Enhanced Manual

Controller only

Ready

Keep Charging

- The battery is fully charged

- Keep the charger (power supply) connected and

operating

Recharge Battery

- The maximum operating time has been

reached

- Connect the charger to the mower

Replace blades

every 200 hours

- An automatic reminder to replace the blades

is displayed every 200 hours

- Replace the blades and restart the counter of the

blades replacement reminder by choosing the

‘

Blades replaced – Clear reminder’

option under

the ‘

User Preferences’

Retry elsewhere

- Calibration failure from interference in the

immediate area

- Move the Robomow 10-12 feet (3-4m) from this

spot and attempt calibration again.

- Displayed only on first use.

- Follow prompts on LCD screen to set country

Set Country

Set Time

- Displayed every time the power pack is taken

out of the mower (reset operation)

- Set real time clock (day and hour)

Skipped: Low bat

- Robomow has skipped the last depart due to

low battery voltage

- Confirm there is enough time between the two

adjacent departures so the battery can be charged

prior the scheduled operation (min 16 hours

between operations)

Skipped: Rain

Only Enhanced Manual

Controller

- Robomow has skipped the last depart due to

rain detection

- It is not recommended to cut wet or damp grass,

but if you choose to override the rain sensor,

change the setting of the ‘Rain sensor’ to ‘off’ under

the ‘User preferences’ menu.

Start Elsewhere

- An unknown fault has occurred and user help

is required

- Manually drive the mower away from this particular

area and restart operation

- Wheel drive motors have been working under

a severe load

- Check to insure the mower is not stuck, allowing the

wheels to slip

Start Inside

- Automatic operation is initiated while

Robomow is placed out of the perimeter wire

lope.

- Place the mower inside the lawn and press the ‘GO’

button.

Thermistors fail

- Faulty / disconnected thermistors (overheat

protection)

- Contact service provider

Time Completed

- The operating time set for that zone has been

reached

- Connect to the charger if all mowing has been

completed for the day.

Waiting for signal…

- Robomow has stopped the operation in Dock

zone, because there is no signal received

from the Base Station

- Check the power to the Base Station.

- There is electrical power interruption. There is

no need to do anything – Robomow will renew

automatically the operation if the power will come

back within an hour from the break.

Содержание City 120













































































Результаты поиска

Содержание City 120

Отзывы:

Похожие инструкции для City 120

Бренды по названию

Популярные бренды

Robomow City 120, Инструкция по эксплуатации и безопасности

Результаты поиска

Содержание City 120

Отзывы:

Похожие инструкции для City 120

Бренды по названию

Популярные бренды