Robomow City 120 Скачать руководство пользователя

Страница: 66 / 76

Chapter 8-8

Robomow City 120

Problem Encountered

Probable Cause/Event

Corrective/User Action

Display

LCD display is in a foreign

language.

The language setting was changed or not cor-

rectly set.

Remove the Manual Controller and follow the sequence

listed;

1. Press ‘

’

button several times

2. Press ‘

’ button twice

3. Press ‘4x

’

arrow key (4 times)

4. Press ‘

’

button once

5. Using the arrow, scroll to the correct language

6. Press ‘

’ to confirm this selection

Problem Encountered

Probable Cause/Event

Corrective/User Action

Mowing

Large patches of uncut grass

remain after Robomow has

completed mowing.

- Power Pack is not fully charged for

operation.

- Connect the charger to the mower and keep it

connected until the

‘Ready–Keep Charging’

message displays in the LCD screen.

- ‘Work Time’ not sufficient for zone size.

- Increase ‘Work Time’ under ‘User Preferences’ OR

set ‘Work Time’ to ‘MAX’

- Power Pack nearing natural end of life

- Replace Power Pack and follow maintenance

instructions in manual.

- Grass is extremely overgrown or very wet.

- Raise cutting height. Always mow the grass

frequently enough to prevent over growth. Refrain

from cutting wet grass.

- Power Pack capacity is damaged from

poor maintenance.

- Replace Power Pack and follow maintenance

instructions in manual.

Poor quality of mowing (grass

clippings are left on the lawn)

- Grass is too high

- It is recommended to cut not more than a 1/3 of the

green part of the grass.

- Set the cutting height to a higher position

- Use Robomow more frequently to maintain your

lawn

The bumper does not activate

when striking an obstacle.

- Grass is wet

- For best cut, operate Robomow when the grass

is dry. It is recommended to mow grass early

afternoon.

- Blades are worn

- Replace blades.

- The obstacle is less than 6 inches (15

cm) in height, is not rigid enough or is

positioned at an angle relative to the

ground preventing square contact with the

outermost surface of the bumper.

- Remove the obstacle

- Setup a wire around the obstacle (refer to 2.2.1/

Chapter 2-3)

- Exclude it from the cutting area with the perimeter

wire.

Содержание City 120













































































Результаты поиска

Содержание City 120

Отзывы:

Похожие инструкции для City 120

Бренды по названию

Популярные бренды

Robomow City 120, Инструкция по эксплуатации и безопасности

Результаты поиска

Содержание City 120

Отзывы:

Похожие инструкции для City 120

Бренды по названию

Популярные бренды