Robomow City 120 Скачать руководство пользователя

Страница: 73 / 76

Chapter 11-1

Accessories

Chapter 11 Accessories

Blade Set
Keep a spare blade

set on hand. Sharp

blades are important for

safety and good cutting

performance.

Power Pack
Convenience of

increasing capacity

with a second battery.

Peg Pack (50)
For larger lawns and

additional zones.

Perimeter Switch
Convenience of having

a switch for each zone

and not moving one

switch from zone to

zone.

Wire connector

Used for repairing

or splicing wires (as

needed).

External Charger
Recharges the primary

or additional Power

Pack outside of the

mower.

Perimeter Wire
For larger lawns and

additional zones.

Batteries Pack for

Perimeter Switch
Preferable for areas

where electricity is

not available or not

close enough to the

Perimeter Switch.

Plot connector
Used for connecting the

completed

perimeter wire set-up to

the Perimeter Switch

Содержание City 120













































































Результаты поиска

Содержание City 120

Отзывы:

Похожие инструкции для City 120

Бренды по названию

Популярные бренды

Robomow City 120, Инструкция по эксплуатации и безопасности

Результаты поиска

Содержание City 120

Отзывы:

Похожие инструкции для City 120

Бренды по названию

Популярные бренды