Robomow City 120 Скачать руководство пользователя

Страница: 63 / 76

Chapter 8-5

Troubleshooting

8.3 Other Problems

Problem Encountered

Probable Cause/Event

Corrective/User Action

Base Station

Robomow does not leave the

Base Station for operation at the

time set in the Weekly Program

- In general, the mower does not depart at the scheduled time, the cause is recorded under ‘

Weekly

Program Display’

(refer to section 5.2 for more details).

- Confirm the time in the mower is set

correctly (day and hour)

- Set the time (See paragraph 5.1)

- Low battery voltage

- Confirm there are minimum 16 hours of charging in

the Base Station before the next scheduled depart

- ‘Auto depart’ is set to ‘off’ (‘Manual depart’

is displayed when the mower is in the

Base Station)

- Change the setting of the ‘Auto depart’ to ‘on’ (See

paragraph 7.3)

Robomow does not detect the

Base Station contacts and/or

‘Front wheel problem’ is dis-

played when the mower is in the

Base Station

- Power supply/charger is not plugged into

the main power supply

- Confirm power supply is plugged into the main

power receptacle.

Robomow reached the Base

Station when its contacts are

above the Base Station contacts

- Height difference between the Base

Station base and the lawn surface at the

entrance to the Base Station

- Confirm the ground before the Base Station is

leveled with the Base Station base – if necessary

fill the area with dirt and level off

Robomow does not detect the

Base Station contacts and/or

‘Front wheel problem’ is dis-

played when the mower is in the

Base Station

- No power to receptacle or main power is

shut off

- Check for power to this main receptacle by plugging

in another appliance.

- Turn power on to the main receptacle.

- Disassemble the Base Station Cover by unscrewing

the screws and check the connection of the power

cable (black) and the wire connector (green).

- Confirm the ‘ON’ light is blinking in the Base

Station.

- Base Station and/or Robomow have burnt

signs and/or corrosion

- Periodically clean the Base Station and the

Robomow contacts using only a damp cloth.

- Contact your service provider if the contacts should

be replaced

- Poor or disconnection of the Base Station

wires (red and green) to the contacts

- Confirm good contacts in the tabs (end of the red

and green wires) to the Base Station contacts.

Robomow is operated in the

zone with the Base Station but

stopped with ‘Recharge battery’

or ‘time completed’ message

- The Robomow was operated from the

lawn (not from the Base Station) when the

main display showed ‘Zone B’

- When operating the Robomow from inside the

lawn, confirm the main display on ‘Dock zone’

Robomow is searching for the

Base Station in zone without

Base Station

- The Robomow was operated from the

lawn in ‘Mowing’ (without ‘Edge’) when the

main display showed ‘Dock zone’

- When operating the Robomow from in Non-Base

Zone, confirm the main display on ‘Zone B’ or start

the operation in ‘Edge’ mode.

Содержание City 120













































































Результаты поиска

Содержание City 120

Отзывы:

Похожие инструкции для City 120

Бренды по названию

Популярные бренды

Robomow City 120, Инструкция по эксплуатации и безопасности

Результаты поиска

Содержание City 120

Отзывы:

Похожие инструкции для City 120

Бренды по названию

Популярные бренды