Robomow City 120 Скачать руководство пользователя

Страница: 60 / 76

Chapter 8-2

Robomow City 120

Message Displayed

Probable Cause/Event

Corrective/User Action

Check Power

- Power supply/charger is not plugged properly

into the main power supply

- Charging plug is not fully inserted into the

charging socket of the mower

- The charging process has stopped due to a

temporary power loss.

Disconnect the charging plug from the mower, confirm power

supply is plugged into the main power receptacle and re-

connect the plug to the mower to resume charging.

- No power to receptacle or main power is shut

off

- Turn power on to the main receptacle.

- The mower contacts do not touch the Base

Station contacts

- Make sure that both mower drive wheels are leveled

with the Base Station base (if necessary fill the area

underneath the drive wheels with dirt)

- The mower or Base Station contacts are dirty

- Clean the contacts with a brush or piece of cloth

- Charging is not detected, although there is

physical contact between the mower and the

Base Station contacts (mower is found in the

Base Station entrance).

- Confirm a good connection of the cables to the Base

Station contacts.

- Check the Charging fuse 5A (remove the plastic cover

below the Manual Controller).

- Mower does not reach the Base Station within

the time and distance limitations.

- Confirm the mower is operated in a Charging zone.

- Confirm the mower is not slipping or stuck on its way

to the Base Station.

Check signal

Press Go

- There is no fitting between the ‘Signal type’

setting in the menu and the signal jumper on

the Perimeter Switch;

- Automatic operation is initiated while

Robomow is placed out of the perimeter wire

lope.

- The perimeter wire is connected to the plot

connector in the wrong polarity.

- Robomow detects signal interferences

from adjacent activated lawn or from other

appliance activated near the zone;

- Set the ‘Signal type’ menu to ‘A’ and confirm the signal

jumper is installed on the Perimeter Switch board; or

alternatively set it to ‘B’ and remove the signal jumper

from the board;

- Place the mower inside the lawn and press the ‘GO’

button.

- Change between the two wires ends that connected to

the plot connector (the green connector that connected

to the Base Station).

- In case of signal interference call the service for help;

- The mower contacts do not touch the Docking

Station contacts

- Make sure that both mower drive wheels are leveled

with the Docking Station base (if necessary fill the area

underneath the drive wheels with dirt)

Docking problem

- The mower or Docking Station contacts are

dirty

- Clean the contacts with a brush or piece of cloth

- Charging is not detected, although there is

physical contact between the mower and the

Docking Station contacts (mower is found in

the Docking Station entrance).

- Turn on the Perimeter Switch

- Confirm a good connection of the cables to the

Docking Station contacts.

- Check the Charging fuse 5A (remove the plastic cover

below the Manual Controller).

- Mower does not reach the Docking Station

within the time and distance limitations.

- Confirm the mower is operated in a docking zone.

- Confirm the mower is not slipping or stuck on its way

to the Docking Station.

Drive Overload
Cooling Wait…

- The drive motors have been working under a

severe load for too long.

- There is no need to do anything – Robomow will renew

automatically the operation, as the drive motor will cool

down.

Drive problem

- Internal failure

- Contact service provider

Содержание City 120













































































Результаты поиска

Содержание City 120

Отзывы:

Похожие инструкции для City 120

Бренды по названию

Популярные бренды

Robomow City 120, Инструкция по эксплуатации и безопасности

Результаты поиска

Содержание City 120

Отзывы:

Похожие инструкции для City 120

Бренды по названию

Популярные бренды